Check out the Zoeller YouTube Channel for Webinars, Tips, Trainings, and Product Videos!

X
MENU CLOSE

X600 Series Sewage Pumps


X600 Series Sewage Pumps

Hazardous Location Pumps


Submersible effluent or dewatering pumps with explosion-proof motors.

  • Features and Benefits
    • cCSAus rated Class I, Division 1, Groups C & D and Class Zone 1, Groups IIA & IIB Construction
    • Tested to FM standards 3600 and 3615 by CSA
    • Non-clogging, semi-open, ductile iron impeller
    • Class 30 cast iron construction
    • All units are double seal for extra motor protection
    • Corrosion-resistant, powder coated epoxy finish
    • Stainless steel screws, washers, tags and seal assembly
    • Explosion-proof motor – 1750 RPM, hermetically-sealed and oil-filled for added heat dissipation
    • Thermal sensor
    • Continuous duty operation in submerged conditions
    • Maximum temperature for sewage or dewatering: 104 °F (40 °C) with 1.2 service factor (1.0 service factor on Model 661)
    • 416 stainless steel motor shaft
    • Tandem stainless steel fitted shaft seals with carbon and ceramic seal faces
    • Seal leak probes
    • Oversized upper and lower ball bearings running in oil bath
    • Buna N square rings and seals
    • All models pass 2-1/2” (63 mm) spherical solids
    • Major width: 17-9/16″ (44.6 cm)
    • Major height: 33-1/4″ (84.5 cm)
    • Specify 3” NPT vertical, 3” horizontal flanged or 4” horizontal flanged discharge
    • 100% computerized tested
    • Nonsparking rail systems available for all models
    • Intrinsically-safe control panels available
    • 1 year limited warranty

    Notes

    Reserve powered design.
    For unusual conditions a reserve safety factor is engineered into the design of every Zoeller pump.

  • Product Specifications

     

    Motor 1 – 7-1/2 HP
    Voltage 200 – 575 V
    Phase 1 or 3 Ph
    Hertz 60 Hz
    RPM 1750 RPM
    Type Capacitor start / capacitor run or 3 phase
    Insulation Class F
    Amps 1.6 – 28.0 Amps
    Operation Nonautomatic
    Discharge Size 3″ NPT (optional 3″ or 4″ flange available)
    Solids Handling 2-1/2″ (63 mm) spherical solids
    Cord Length 25′ (8 m) standard
    Cord Type UL listed power and sensor cord
    Max Head 65′ (19.8 m)
    Max Flow Rate 600 GPM (2,271 LPM)
    Max Operating Temperature 104 °F (40 °C)
    Cooling Oil filled with finned housings
    Motor Protection Thermal sensors and moisture sensors
    Cap Cast iron
    Motor Housing Cast iron
    Pump Housing Cast iron
    Base Cast iron
    Upper Bearing Oversized ball bearing
    Lower Bearing Oversized ball bearing
    Mechanical Seals Carbon and ceramic with stainless steel parts
    Impeller Type Semi-open
    Impeller Ductile iron
    Hardware Stainless steel
    Motor Shaft 416 stainless steel
     

    Powder Coated Tough      SSPMA      CSA

  • Literature

    Warning

    Not for use in acidic, methanol or ethyl acetate atmospheres.

    Sales Literature

    Model Comparison Charts

    • Product Model Comparison Chart: 60hz
      model seal mode volts phase amps hp hz lbs kg
      EX611 Double Non 230 1 6.9 1 60 295 133
      JX611 Double Non 200 3 4.8 1 60 295 133
      FX611 Double Non 230 3 4.2 1 60 295 133
      GX611 Double Non 460 3 2.1 1 60 295 133
      BAX611 Double Non 575 3 1.7 1 60 295 133
      EX621 Double Non 230 1 8.9 1-1/2 60 295 133
      JX621 Double Non 200 3 5.9 1-1/2 60 295 133
      FX621 Double Non 230 3 5.1 1-1/2 60 295 133
      GX621 Double Non 460 3 2.6 1-1/2 60 295 133
      BAX621 Double Non 575 3 2.0 1-1/2 60 295 133
      EX631 Double Non 230 1 14.5 2 60 295 133
      JX631 Double Non 200 3 7.8 2 60 295 133
      FX631 Double Non 230 3 6.8 2 60 295 133
      GX631 Double Non 460 3 3.4 2 60 295 133
      BAX631 Double Non 575 3 2.7 2 60 295 133
      EX641 Double Non 230 1 17.0 3 60 295 133
      JX641 Double Non 200 3 11.0 3 60 295 133
      FX641 Double Non 230 3 9.6 3 60 295 133
      GX641 Double Non 460 3 4.8 3 60 295 133
      BAX641 Double Non 575 3 3.9 3 60 295 133
      EX651 Double Non 230 1 28.0 5 60 295 133
      JX651 Double Non 200 3 17.5 5 60 295 133
      FX651 Double Non 230 3 15.2 5 60 295 133
      GX651 Double Non 460 3 7.6 5 60 295 133
      BAX651 Double Non 575 3 6.1 5 60 295 133
      JX661 Double Non 200 3 25.3 7-1/2 60 295 133
      FX661 Double Non 230 3 22.0 7-1/2 60 295 133
      GX661 Double Non 460 3 11.0 7-1/2 60 295 133
      BAX661 Double Non 575 3 9.0 7-1/2 60 295 133

    –>

     

    <!–

    –>
    013859X, Performance Chart, X600 Series: 60 Hz
    <!–

    –>

     

–>

 


  • zepa0548, Dimensional Drawing, X600 Series, 3″ Vertical Discharge
    <!–
  • –>

     


  • zepa0549, Dimensional Drawing, X600 Series, 3″ Horizontal Discharge
    <!–
  • –>

     


  • zepa0550, Dimensional Drawing, X600 Series, 3″ Vertical Discharge 39-0124, 39-0125
    <!–
  • –>

     


  • zepa0551, Dimensional Drawing, X600 Series, 3″ Horizontal Discharge 39-0095
    <!–
  • –>

     


  • zepa0552, Dimensional Drawing, X600 Series, 4″ Horizontal Discharge 39-0017
    <!–
  • –>

     


    BIM, Revit, X600 Series, 3″ & 4″ Horizontal Discharge
    <!–

    –>

     

    BIM, Revit, X600 Series, 3″ Vertical Discharge
    <!–

    –>

     

  • Packages and Accessories
    • cCSAus rated Class I, Division 1, Groups C & D and Class Zone 1, Groups IIA & IIB Construction
    • Tested to FM standards 3600 and 3615 by CSA
    • Non-clogging, semi-open, ductile iron impeller
    • Class 30 cast iron construction
    • All units are double seal for extra motor protection
    • Corrosion-resistant, powder coated epoxy finish
    • Stainless steel screws, washers, tags and seal assembly
    • Explosion-proof motor – 1750 RPM, hermetically-sealed and oil-filled for added heat dissipation
    • Thermal sensor
    • Continuous duty operation in submerged conditions
    • Maximum temperature for sewage or dewatering: 104 °F (40 °C) with 1.2 service factor (1.0 service factor on Model 661)
    • 416 stainless steel motor shaft
    • Tandem stainless steel fitted shaft seals with carbon and ceramic seal faces
    • Seal leak probes
    • Oversized upper and lower ball bearings running in oil bath
    • Buna N square rings and seals
    • All models pass 2-1/2” (63 mm) spherical solids
    • Major width: 17-9/16″ (44.6 cm)
    • Major height: 33-1/4″ (84.5 cm)
    • Specify 3” NPT vertical, 3” horizontal flanged or 4” horizontal flanged discharge
    • 100% computerized tested
    • Nonsparking rail systems available for all models
    • Intrinsically-safe control panels available
    • 1 year limited warranty

    Notes

    Reserve powered design.
    For unusual conditions a reserve safety factor is engineered into the design of every Zoeller pump.

     

    Motor 1 – 7-1/2 HP
    Voltage 200 – 575 V
    Phase 1 or 3 Ph
    Hertz 60 Hz
    RPM 1750 RPM
    Type Capacitor start / capacitor run or 3 phase
    Insulation Class F
    Amps 1.6 – 28.0 Amps
    Operation Nonautomatic
    Discharge Size 3″ NPT (optional 3″ or 4″ flange available)
    Solids Handling 2-1/2″ (63 mm) spherical solids
    Cord Length 25′ (8 m) standard
    Cord Type UL listed power and sensor cord
    Max Head 65′ (19.8 m)
    Max Flow Rate 600 GPM (2,271 LPM)
    Max Operating Temperature 104 °F (40 °C)
    Cooling Oil filled with finned housings
    Motor Protection Thermal sensors and moisture sensors
    Cap Cast iron
    Motor Housing Cast iron
    Pump Housing Cast iron
    Base Cast iron
    Upper Bearing Oversized ball bearing
    Lower Bearing Oversized ball bearing
    Mechanical Seals Carbon and ceramic with stainless steel parts
    Impeller Type Semi-open
    Impeller Ductile iron
    Hardware Stainless steel
    Motor Shaft 416 stainless steel
     

    Powder Coated Tough      SSPMA      CSA

    Warning

    Not for use in acidic, methanol or ethyl acetate atmospheres.

    Sales Literature

    Model Comparison Charts

    • Product Model Comparison Chart: 60hz
      model seal mode volts phase amps hp hz lbs kg
      EX611 Double Non 230 1 6.9 1 60 295 133
      JX611 Double Non 200 3 4.8 1 60 295 133
      FX611 Double Non 230 3 4.2 1 60 295 133
      GX611 Double Non 460 3 2.1 1 60 295 133
      BAX611 Double Non 575 3 1.7 1 60 295 133
      EX621 Double Non 230 1 8.9 1-1/2 60 295 133
      JX621 Double Non 200 3 5.9 1-1/2 60 295 133
      FX621 Double Non 230 3 5.1 1-1/2 60 295 133
      GX621 Double Non 460 3 2.6 1-1/2 60 295 133
      BAX621 Double Non 575 3 2.0 1-1/2 60 295 133
      EX631 Double Non 230 1 14.5 2 60 295 133
      JX631 Double Non 200 3 7.8 2 60 295 133
      FX631 Double Non 230 3 6.8 2 60 295 133
      GX631 Double Non 460 3 3.4 2 60 295 133
      BAX631 Double Non 575 3 2.7 2 60 295 133
      EX641 Double Non 230 1 17.0 3 60 295 133
      JX641 Double Non 200 3 11.0 3 60 295 133
      FX641 Double Non 230 3 9.6 3 60 295 133
      GX641 Double Non 460 3 4.8 3 60 295 133
      BAX641 Double Non 575 3 3.9 3 60 295 133
      EX651 Double Non 230 1 28.0 5 60 295 133
      JX651 Double Non 200 3 17.5 5 60 295 133
      FX651 Double Non 230 3 15.2 5 60 295 133
      GX651 Double Non 460 3 7.6 5 60 295 133
      BAX651 Double Non 575 3 6.1 5 60 295 133
      JX661 Double Non 200 3 25.3 7-1/2 60 295 133
      FX661 Double Non 230 3 22.0 7-1/2 60 295 133
      GX661 Double Non 460 3 11.0 7-1/2 60 295 133
      BAX661 Double Non 575 3 9.0 7-1/2 60 295 133

    –>

     

    <!–

    –>
    013859X, Performance Chart, X600 Series: 60 Hz
    <!–

    –>

     

    Design Tools

    –>

     


  • zepa0548, Dimensional Drawing, X600 Series, 3″ Vertical Discharge
    <!–
  • –>

     


  • zepa0549, Dimensional Drawing, X600 Series, 3″ Horizontal Discharge
    <!–

    –>

     


  • zepa0550, Dimensional Drawing, X600 Series, 3″ Vertical Discharge 39-0124, 39-0125
    <!–

    –>

     


  • zepa0551, Dimensional Drawing, X600 Series, 3″ Horizontal Discharge 39-0095
    <!–

    –>

     


  • zepa0552, Dimensional Drawing, X600 Series, 4″ Horizontal Discharge 39-0017
    <!–

    –>

     


    BIM, Revit, X600 Series, 3″ & 4″ Horizontal Discharge
    <!–

    –>

     

    BIM, Revit, X600 Series, 3″ Vertical Discharge
    <!–

    –>

     

  • Accessories

    en_USEnglish