
Check out the Zoeller YouTube Channel for Webinars, Tips, Trainings, and Product Videos!
Effluent Pumps
Effluent or dewatering submersible pumps for septic tanks, low pressure pipe (LPP) and enhanced flow STEP systems.
Consult Factory for Special Applications
Notes
The sizing of effluent systems normally requires variable level float(s) controls and properly sized basins to achieve required pumping cycles or dosing timers with non-automatic pumps.
Reserve Powered Design.
For unusual conditions a reserve safety factor is engineered into the design of every Zoeller pump.
Motor | 1/2 HP | |
Voltage | 115 or 230 V | |
Phase | 1 Ph | |
Hertz | 60 Hz | |
RPM | 1725 RPM | |
Type | Permanent split capacitor | |
Insulation | Class B | |
Amps | 4.7 – 9.4 Amps | |
Operation | Automatic or nonautomatic | |
Auto On / Off Points | 9-1/2″ / 3″ (24 cm / 8 cm) | |
Discharge Size | 1-1/2″ NPT | |
Solids Handling | 1/2″ (12 mm) spherical solids | |
Cord Length | 15′ (5 m) standard | |
Cord Type | UL listed | |
Max Head | 23′ (7 m) | |
Max Flow Rate | 72 GPM (273 LPM) | |
Max Operating Temperature | 130 °F (54 °C) | |
Cooling | Oil filled | |
Motor Protection | Auto reset thermal overload | |
Cap | Cast iron | |
Motor Housing | Cast iron | |
Pump Housing | Cast iron | |
Base | Engineered Thermoplastic | |
Upper Bearing | Oil-fed cast iron | |
Lower Bearing | Oil-fed cast iron | |
Mechanical Seals | Carbon and ceramic | |
Impeller Type | Non-clogging vortex | |
Impeller | Engineered plastic | |
Hardware | Stainless steel | |
Motor Shaft | AISI 1215 cold roll steel | |
Gasket | Neoprene | |
|
Consult Factory for Special Applications
Notes
The sizing of effluent systems normally requires variable level float(s) controls and properly sized basins to achieve required pumping cycles or dosing timers with non-automatic pumps.
Reserve Powered Design.
For unusual conditions a reserve safety factor is engineered into the design of every Zoeller pump.
Motor | 1/2 HP | |
Voltage | 115 or 230 V | |
Phase | 1 Ph | |
Hertz | 60 Hz | |
RPM | 1725 RPM | |
Type | Permanent split capacitor | |
Insulation | Class B | |
Amps | 4.7 – 9.4 Amps | |
Operation | Automatic or nonautomatic | |
Auto On / Off Points | 9-1/2″ / 3″ (24 cm / 8 cm) | |
Discharge Size | 1-1/2″ NPT | |
Solids Handling | 1/2″ (12 mm) spherical solids | |
Cord Length | 15′ (5 m) standard | |
Cord Type | UL listed | |
Max Head | 23′ (7 m) | |
Max Flow Rate | 72 GPM (273 LPM) | |
Max Operating Temperature | 130 °F (54 °C) | |
Cooling | Oil filled | |
Motor Protection | Auto reset thermal overload | |
Cap | Cast iron | |
Motor Housing | Cast iron | |
Pump Housing | Cast iron | |
Base | Engineered Thermoplastic | |
Upper Bearing | Oil-fed cast iron | |
Lower Bearing | Oil-fed cast iron | |
Mechanical Seals | Carbon and ceramic | |
Impeller Type | Non-clogging vortex | |
Impeller | Engineered plastic | |
Hardware | Stainless steel | |
Motor Shaft | AISI 1215 cold roll steel | |
Gasket | Neoprene | |
|