Check out the Zoeller YouTube Channel for Webinars, Tips, Trainings, and Product Videos!

X
MENU CLOSE

Model 95 Sump Pump


Model 95 Sump Pump

Residential Sump Pits

PREMIUM SERIES submersible pump for dewatering (sump) systems

  • Features and Benefits
    • Corrosion-resistant, powder coated epoxy finish
    • Durable, cast iron construction
    • Cast iron switch case, motor, pump housing and base
    • Viton outer switch boot
    • No sheet metal parts to rust or corrode
    • All castings are cast iron class 25-30 25000# tensile strength
    • Stainless steel screws, guard, handle, arm and seal assembly
    • Float-operated, submersible, 2-pole mechanical switch integrating advanced switch technology
    • Permanent split capacitor motor, oil-filled and hermetically-sealed, automatic reset thermal overload protection
    • Bearings – upper and lower oil-fed cast iron
    • Carbon and ceramic shaft seal
    • Entire unit pressure-tested after assembly
    • Watertight, neoprene square ring between motor and pump housing
    • Maximum temperature for effluent or dewatering: 130 °F (54 °C)
    • Passes 1/2” (12 mm) spherical solids
    • No screens to clog
    • 1-1/2” NPT discharge (1-1/2” x 2” PVC adapter included with BN and BE Models)
    • On point: 9-1/2” (24 cm)
    • Off point: 3” (8 cm)
    • Major width: 10-1/8″ (31 cm)
    • Major height: 12-1/8″ (30 cm)
    • Simplex and duplex systems available
    • 5 year limited warranty

    Consult Factory for Special Applications

    • Electrical alternators for duplex systems are available and supplied with an alarm
    • Mechanical alternators for duplex systems are available with or without alarm switches
    • Variable level float switches are available for controlling single and three phase systems
    • Refer to FM1922 and FM0806 for temperatures above 130 °F (54 °C)

    Notes

    The sizing of effluent systems normally requires variable level float(s) controls and properly sized basins to achieve required pumping cycles or dosing timers with non-automatic pumps.

    Reserve Powered Design.

    For unusual conditions a reserve safety factor is engineered into the design of every Zoeller pump.

  • Product Specifications
    Motor 1/2
    Voltage 115
    Phase 1 Ph
    Hertz 60 Hz
    RPM 3450
    Type Permanent split capacitor
    Insulation Class B
    Amps 10.5
    Operation Automatic
    Auto On / Off Points 9-1/2″ (24 cm) / 2-1/2″ (6.4 cm)
    Discharge Size 1-1/2″ NPT
    Solids Handling 1/2″ (12 mm) spherical solids
    Cord Length 15′ (4.6 m)
    Cord Type UL listed, 3-wire, grounded plug
    Max Head 26′ (7.9 m)
    Max Flow Rate 80 GPM (303 LPM)
    Max Operating Temperature 130° F (54° C)
    Cooling Oil filled
    Motor Protection Auto reset thermal overload
    Cap Cast iron
    Motor Housing Cast iron
    Pump Housing Cast iron
    Base Cast iron
    Upper Bearing Sleeve bearing
    Lower Bearing Ball bearing
    Mechanical Seals Carbon and ceramic
    Impeller Type Non-clogging vortex
    Impeller Engineered thermoplastic
    Hardware Stainless steel
    Motor Shaft AISI 1215 cold rolled steel
    Gasket Neoprene
     

                 

  • Literature
  • Package and Accessories
  • Corrosion-resistant, powder coated epoxy finish
  • Durable, cast iron construction
  • Cast iron switch case, motor, pump housing and base
  • Viton outer switch boot
  • No sheet metal parts to rust or corrode
  • All castings are cast iron class 25-30 25000# tensile strength
  • Stainless steel screws, guard, handle, arm and seal assembly
  • Float-operated, submersible, 2-pole mechanical switch integrating advanced switch technology
  • Permanent split capacitor motor, oil-filled and hermetically-sealed, automatic reset thermal overload protection
  • Bearings – upper and lower oil-fed cast iron
  • Carbon and ceramic shaft seal
  • Entire unit pressure-tested after assembly
  • Watertight, neoprene square ring between motor and pump housing
  • Maximum temperature for effluent or dewatering: 130 °F (54 °C)
  • Passes 1/2” (12 mm) spherical solids
  • No screens to clog
  • 1-1/2” NPT discharge (1-1/2” x 2” PVC adapter included with BN and BE Models)
  • On point: 9-1/2” (24 cm)
  • Off point: 3” (8 cm)
  • Major width: 10-1/8″ (31 cm)
  • Major height: 12-1/8″ (30 cm)
  • Simplex and duplex systems available
  • 5 year limited warranty

Consult Factory for Special Applications

  • Electrical alternators for duplex systems are available and supplied with an alarm
  • Mechanical alternators for duplex systems are available with or without alarm switches
  • Variable level float switches are available for controlling single and three phase systems
  • Refer to FM1922 and FM0806 for temperatures above 130 °F (54 °C)

Notes

The sizing of effluent systems normally requires variable level float(s) controls and properly sized basins to achieve required pumping cycles or dosing timers with non-automatic pumps.

Reserve Powered Design.

For unusual conditions a reserve safety factor is engineered into the design of every Zoeller pump.

Motor 1/2
Voltage 115
Phase 1 Ph
Hertz 60 Hz
RPM 3450
Type Permanent split capacitor
Insulation Class B
Amps 10.5
Operation Automatic
Auto On / Off Points 9-1/2″ (24 cm) / 2-1/2″ (6.4 cm)
Discharge Size 1-1/2″ NPT
Solids Handling 1/2″ (12 mm) spherical solids
Cord Length 15′ (4.6 m)
Cord Type UL listed, 3-wire, grounded plug
Max Head 26′ (7.9 m)
Max Flow Rate 80 GPM (303 LPM)
Max Operating Temperature 130° F (54° C)
Cooling Oil filled
Motor Protection Auto reset thermal overload
Cap Cast iron
Motor Housing Cast iron
Pump Housing Cast iron
Base Cast iron
Upper Bearing Sleeve bearing
Lower Bearing Ball bearing
Mechanical Seals Carbon and ceramic
Impeller Type Non-clogging vortex
Impeller Engineered thermoplastic
Hardware Stainless steel
Motor Shaft AISI 1215 cold rolled steel
Gasket Neoprene