Check out the Zoeller YouTube Channel for Webinars, Tips, Trainings, and Product Videos!

X
MENU CLOSE

Model 211 Sewage Pump


Model 211 Sewage Pump

Obsolete Products

This product is obsolete. For current product please see Model 212 Sewage Pump.

  • Features & Benefits

    This product is obsolete. For current product please see Model 212 Sewage Pump.

    • Non-corrosive engineered plastic motor housing, pump housing, base and impeller
    • Oil free
    • No sheet metal parts to rust or corrode
    • All stainless steel screws, switch arm and lower motor housing
    • 2 pole float operated mechanical switch
    • Solid polypropylene float
    • Maximum temperature for dewatering: 110 °F (43 °C)
    • Passes 2″ (50 mm) spherical solids
    • 2″ NPT discharge
    • On point: 13″ (33 cm)
    • Off point: 5-3/4″ (14.6 cm)
    • Major width: 9-5/16″ (23.7 cm)
    • Major height: 15-7/8″ (40.3 cm)
    • All models completely submersible and hermetically sealed
    • Watertight and dust tight
    • 2 year limited warranty

    Models available:

    • Automatic
    • Nonautomatic

    Consult factory for special applications:

    • Variable level float switches available
    • Variable level long cycle systems available
    • Alarm systems available

    Notes
    Recommended for 2″ pipe only

    The sizing of effluent systems normally requires variable level float(s) controls and properly sized basins to achieve required pumping cycles or dosing timers with non-automatic pumps.

    Reserve powered design.

    For unusual conditions a reserve safety factor is engineered into the design of every Zoeller pump.

  • Product Specifications

     

    Motor 4/10 HP
    Voltage 115 V
    Phase 1 Ph
    Hertz 60 Hz
    RPM 3400 RPM
    Type Permanent split capacitor
    Insulation Class B
    Amps 5.5 Amps
    Operation Automatic or nonautomatic
    Auto On / Off Points 13″ / 5-3/4″ (33 cm / 14.6 cm)
    Discharge Size 2″ NPT
    Solids Handling 2″ (50 mm) spherical solids
    Cord Length 10′ (3 m) auto, 15′ (5 m) non auto
    Cord Type UL listed, 3-prong plug
    Max Head 19.5′ (5.9 m)
    Max Flow Rate 82 GPM (310 LPM)
    Max Operating Temperature 110 °F (43 °C)
    Cooling Oil free
    Motor Protection Auto reset thermal overload
    Motor Housing Engineered plastic
    Pump Housing Engineered plastic
    Base Engineered plastic
    Upper Bearing Ball bearing
    Lower Bearing Ball bearing
    Mechanical Seals Carbon and ceramic
    Impeller Type Non-clogging vortex
    Impeller Engineered plastic
    Hardware Stainless steel
    Motor Shaft 410 stainless steel
    Gasket Buna-N O-Ring
     

    cCSAus      SSPMA

  • Literature
  • Packages & Accessories

This product is obsolete. For current product please see Model 212 Sewage Pump.

  • Non-corrosive engineered plastic motor housing, pump housing, base and impeller
  • Oil free
  • No sheet metal parts to rust or corrode
  • All stainless steel screws, switch arm and lower motor housing
  • 2 pole float operated mechanical switch
  • Solid polypropylene float
  • Maximum temperature for dewatering: 110 °F (43 °C)
  • Passes 2″ (50 mm) spherical solids
  • 2″ NPT discharge
  • On point: 13″ (33 cm)
  • Off point: 5-3/4″ (14.6 cm)
  • Major width: 9-5/16″ (23.7 cm)
  • Major height: 15-7/8″ (40.3 cm)
  • All models completely submersible and hermetically sealed
  • Watertight and dust tight
  • 2 year limited warranty

Models available:

  • Automatic
  • Nonautomatic

Consult factory for special applications:

  • Variable level float switches available
  • Variable level long cycle systems available
  • Alarm systems available

Notes
Recommended for 2″ pipe only

The sizing of effluent systems normally requires variable level float(s) controls and properly sized basins to achieve required pumping cycles or dosing timers with non-automatic pumps.

Reserve powered design.

For unusual conditions a reserve safety factor is engineered into the design of every Zoeller pump.

 

Motor 4/10 HP
Voltage 115 V
Phase 1 Ph
Hertz 60 Hz
RPM 3400 RPM
Type Permanent split capacitor
Insulation Class B
Amps 5.5 Amps
Operation Automatic or nonautomatic
Auto On / Off Points 13″ / 5-3/4″ (33 cm / 14.6 cm)
Discharge Size 2″ NPT
Solids Handling 2″ (50 mm) spherical solids
Cord Length 10′ (3 m) auto, 15′ (5 m) non auto
Cord Type UL listed, 3-prong plug
Max Head 19.5′ (5.9 m)
Max Flow Rate 82 GPM (310 LPM)
Max Operating Temperature 110 °F (43 °C)
Cooling Oil free
Motor Protection Auto reset thermal overload
Motor Housing Engineered plastic
Pump Housing Engineered plastic
Base Engineered plastic
Upper Bearing Ball bearing
Lower Bearing Ball bearing
Mechanical Seals Carbon and ceramic
Impeller Type Non-clogging vortex
Impeller Engineered plastic
Hardware Stainless steel
Motor Shaft 410 stainless steel
Gasket Buna-N O-Ring
 

cCSAus      SSPMA