Check out the Zoeller YouTube Channel for Webinars, Tips, Trainings, and Product Videos!

X
MENU CLOSE

Intermittent High Temperature Pumps


Intermittent High Temperature Pumps

High Temperature Water Pumps

Submersible pumps for use in dewatering applications. Intermittent use up to 200 °F (93 °C).

  • All models are designed to meet specifications with assurance by using high temperature parts rated for intermittent 200 °F (93 °C) contact.
  • High temperature switch components rated for intermittent service up to 200 °F (93 °C)
  • Available in a variety of styles and performances
  • All models built to last
  • High temperature motor leads and thermal overload protection
  • 100% corrosion-resistant, powder coated epoxy finish
  • 10′ (3 m) cord, high temperature, adjustable float-operated mechanical switch mounts directly to the discharge pipe
  • 1-1/2″, 2″ or 3″ discharge
  • Adjustable float switch is not intended for continuous contact with 200 °F (93 °C) water.
  • All stainless steel fittings
  • 100% factory tested and approved
  • Boiler blow down
  • Hot water transfer
  • Plant wash down
  • Transformer vaults
  • Industrial steam cleaning
  • 16 guage, 2 conductor SOOW switch cordage
  • Float housing constructed of high impact ABS
  • 13.0 Amps (max) steady state
  • Intermittent direct contact with up to 200 °F (93 °C) water
  • Turbulence-resistant float switch
  • Adjustable pumping range (see chart)
  • Unlimited repetitive exposures are permissible for applications below 180 °F (82 °C)
  • 1 year limited warranty

 

Motor 3/10 – 1/2 HP
Voltage 115 or 230 V
Phase 1 Ph
Hertz 60 Hz
RPM 1725 RPM
Amps 4.7 – 10.7 Amps
Operation automatic
Discharge Size 1-1/2″ – 3″
Solids Handling 1/2″ – 3/4″ (13 mm – 19 mm)
Cord Length 15′ (5 m) standard
Cord Type 16-3 SOOW cord
Max Head 25′ (7.6 m)
Max Flow Rate 115 GPM (435 LPM)
Max Operating Temperature 200 °F (93 °C)
Cooling Oil filled
Motor Protection High temperature thermal overload
Motor Housing Cast iron
Pump Housing Cast iron
Base Cast iron
Upper Bearing Varies based on package
Lower Bearing Varies based on package
Mechanical Seals Carbon and NI-resist
Impeller Type Non-clogging vortex
Impeller Cast iron
Hardware Stainless steel
Motor Shaft AISI cold rolled steel
Gasket Neoprene
 

Powder Coated Tough

Sales Literature

Model Comparison Charts

  • Product Model Comparison Chart: 60hz
    model seal mode volts phase amps hp hz lbs kg
    BN2057 Single Non 115 1 9.7 3/10 60 28 13
    BE2057 Single Non 230 1 4.8 3/10 60 28 13
    BN2098 Single Non 115 1 9.4 1/2 60 39 18
    BE2098 Single Non 230 1 4.7 1/2 60 39 18
    BN2137 Single Non 115 1 10.7 1/2 60 46 21
    BE2137 Single Non 230 1 5.8 1/2 60 46 21
    BN2282 Single Non 115 1 10.3 1/2 60 84 38
    BE2282 Single Non 230 1 5.0 1/2 60 84 38

 

Drawing, Model 2137, SK1018

Drawing, Model 2137, SK1018