Check out the Zoeller YouTube Channel for Webinars, Tips, Trainings, and Product Videos!

X
MENU CLOSE

270 Series Sewage Pumps


270 Series Sewage Pumps

Commercial Use Sewage Pumps

Submersible water pump for moving sewage or effluent

  • Features & Benefits
    • Durable, ASTM Class 25 cast iron motor housing cover and pump housing
    • Engineered plastic base on model 270
    • Not affected by materials normally found in drainage and sewage sumps
    • Stainless steel screws, bolts and handle
    • Oil-filled, hermetically-sealed, automatic reset thermal overload protected motor
    • Neoprene square ring & gasket
    • Carbon and ceramic shaft seal
    • 4270 series double seal pump available
    • Cast iron base on 4270
    • Upper sleeve bearing and lower ball bearing running in a bath of oil
    • Passes 2” (50 mm) spherical solids
    • 2” NPT discharge
    • Corrosion-resistant, powder coated epoxy finish
    • Models available packaged with a piggyback variable level float switch
    • Simplex and duplex systems available
    • Packaged systems available
    • 1 year limited warranty

    Consult factory for special applications:

    • Electrical alternators for duplex systems available with variable level control switches
    • Minimum recommended basin size (small load applications): simplex – 24” x 30” (60.9 x 76.2 cm), duplex – 36” x 36” (91.4 x 91.4 cm)
    • Standard model 270 – 49 lbs (22 kg)
    • Standard model 4270 – 73 lbs (33 kg)
    • High water alarms available
    • Mechanical alternators available for duplex systems

    Notes
    The sizing of effluent systems normally requires variable level float(s) controls and properly sized basins to achieve required pumping cycles or dosing timers with non-automatic pumps.

    Reserve powered design.

    For unusual conditions a reserve safety factor is engineered into the design of every Zoeller pump.

    *May be used in those states where codes do not restrict solids size in effluent systems.

  • Product Specifications
    Motor 1 HP
    Voltage 115 or 230 V
    Phase 1 Ph
    Hertz 60 Hz
    RPM 3450 RPM
    Type Permanent split capacitor
    Insulation Class B
    Amps 7.5 – 15.0 Amps
    Operation Automatic or nonautomatic
    Discharge Size 2″ NPT
    Solids Handling 2″ (50 mm) spherical solids
    Cord Length 20′ (6 m) standard
    Cord Type UL listed, 3-wire neoprene cord and plug
    Max Head 29′ (8.8 m)
    Max Flow Rate 132 GPM (500 LPM)
    Max Operating Temperature 130 °F (54 °C)
    Cooling Oil filled
    Motor Protection Auto reset thermal overload
    Cap Cast iron
    Motor Housing Cast iron
    Pump Housing Cast iron
    Base Engineered plastic or cast iron
    Upper Bearing Sleeve bearing
    Lower Bearing Ball bearing
    Mechanical Seals Carbon and ceramic
    Impeller Type Non-clogging vortex
    Impeller Engineered plastic
    Hardware Stainless steel
    Motor Shaft JIS S45C steel
    Gasket Neoprene
     

    cCSAus      SSPMA      Powder Coated Tough

  • Literature

    Maximum temperature of sewage or dewatering must be limited to 130°F (54°C). For over 130°F (54°C) special quotation required.

    Sales Literature

    Model Comparison Charts

    • Product Model Comparison Chart: 60hz
      model seal mode volts phase amps hp hz lbs kg
      BN270 Single Auto 115 1 15.0 1 60 49 22
      N270 Single Non 115 1 15.0 1 60 49 22
      N4270 Double Non 115 1 15.0 1 60 49 22
      E270 Single Non 230 1 7.5 1 60 73 33
      BE270 Single Auto 230 1 7.5 1 60 73 33
      E4270 Double Non 230 1 7.5 1 60 73 33
  • Packages & Accessories
  • Durable, ASTM Class 25 cast iron motor housing cover and pump housing
  • Engineered plastic base on model 270
  • Not affected by materials normally found in drainage and sewage sumps
  • Stainless steel screws, bolts and handle
  • Oil-filled, hermetically-sealed, automatic reset thermal overload protected motor
  • Neoprene square ring & gasket
  • Carbon and ceramic shaft seal
  • 4270 series double seal pump available
  • Cast iron base on 4270
  • Upper sleeve bearing and lower ball bearing running in a bath of oil
  • Passes 2” (50 mm) spherical solids
  • 2” NPT discharge
  • Corrosion-resistant, powder coated epoxy finish
  • Models available packaged with a piggyback variable level float switch
  • Simplex and duplex systems available
  • Packaged systems available
  • 1 year limited warranty

Consult factory for special applications:

  • Electrical alternators for duplex systems available with variable level control switches
  • Minimum recommended basin size (small load applications): simplex – 24” x 30” (60.9 x 76.2 cm), duplex – 36” x 36” (91.4 x 91.4 cm)
  • Standard model 270 – 49 lbs (22 kg)
  • Standard model 4270 – 73 lbs (33 kg)
  • High water alarms available
  • Mechanical alternators available for duplex systems

Notes
The sizing of effluent systems normally requires variable level float(s) controls and properly sized basins to achieve required pumping cycles or dosing timers with non-automatic pumps.

Reserve powered design.

For unusual conditions a reserve safety factor is engineered into the design of every Zoeller pump.

*May be used in those states where codes do not restrict solids size in effluent systems.

Motor 1 HP
Voltage 115 or 230 V
Phase 1 Ph
Hertz 60 Hz
RPM 3450 RPM
Type Permanent split capacitor
Insulation Class B
Amps 7.5 – 15.0 Amps
Operation Automatic or nonautomatic
Discharge Size 2″ NPT
Solids Handling 2″ (50 mm) spherical solids
Cord Length 20′ (6 m) standard
Cord Type UL listed, 3-wire neoprene cord and plug
Max Head 29′ (8.8 m)
Max Flow Rate 132 GPM (500 LPM)
Max Operating Temperature 130 °F (54 °C)
Cooling Oil filled
Motor Protection Auto reset thermal overload
Cap Cast iron
Motor Housing Cast iron
Pump Housing Cast iron
Base Engineered plastic or cast iron
Upper Bearing Sleeve bearing
Lower Bearing Ball bearing
Mechanical Seals Carbon and ceramic
Impeller Type Non-clogging vortex
Impeller Engineered plastic
Hardware Stainless steel
Motor Shaft JIS S45C steel
Gasket Neoprene
 

cCSAus      SSPMA      Powder Coated Tough

Maximum temperature of sewage or dewatering must be limited to 130°F (54°C). For over 130°F (54°C) special quotation required.

Sales Literature

Model Comparison Charts

  • Product Model Comparison Chart: 60hz
    model seal mode volts phase amps hp hz lbs kg
    BN270 Single Auto 115 1 15.0 1 60 49 22
    N270 Single Non 115 1 15.0 1 60 49 22
    N4270 Double Non 115 1 15.0 1 60 49 22
    E270 Single Non 230 1 7.5 1 60 73 33
    BE270 Single Auto 230 1 7.5 1 60 73 33
    E4270 Double Non 230 1 7.5 1 60 73 33