
Check out the Zoeller YouTube Channel for Webinars, Tips, Trainings, and Product Videos!
Residential Use Sewage Pumps
Submersible sewage, effluent or dewatering pump
Zoller Pump Company’s 260 Series Sewage Pumps are designed to pump waste to sewage systems or septic tanks in residential or light commercial applications. This series is designed to transfer groundwater, raw sewage or effluent with a no-hassle, effortless performance. The benefits of this series include discharge sizes of 2 or 3 inches with the capacity to pass 2-inch solids.
An innovative vortex impeller pushes fluid against a pump volute using centrifugal force. The impeller vanes and fluid never make contact as the system operates, helping the design stay clear and clog-free. The float-operated, completely submersible pumps have watertight and dust-tight seals to maintain ideal conditions.
This sump pump comes with a protective finish of powder-coated epoxy for corrosion resistance. Other durable features of this sump pump include an assembly with stainless steel fasteners and cast iron construction for the switch cap, motor, and pump housing. Our accessory options include variable-level control switches that allow you to monitor fluid levels with ease.
Consult factory for special applications:
Tank Diameter | Gallons / Liters Pumped |
18” (46 cm) simplex | 8 gallons / 36 liters |
24” (60 cm) simplex | 15 gallons / 68 liters |
30” (76 cm) duplex | 22 gallons / 100 liters |
36” (91 cm) duplex | 33 gallons / 150 liters |
48” (122 cm) duplex | 60 gallons / 273 liters |
Notes
The sizing of effluent systems normally requires variable level float(s) controls and properly sized basins to achieve required pumping cycles or dosing timers with non-automatic pumps.
Reserve powered design.
For unusual conditions a reserve safety factor is engineered into the design of every Zoeller pump.
*May be used in those states where codes do not restrict solids size in effluent systems.
** See charts for UL and CSA listings.
Motor | 1/2 HP | |
Voltage | 115 – 460 V | |
Phase | 1 or 3 Ph | |
Hertz | 60 Hz | |
RPM | 1750 RPM | |
Type | Split phase or 3 phase | |
Insulation | Class B | |
Amps | 1.5 – 9.4 Amps | |
Operation | Automatic or nonautomatic | |
Auto On / Off Points | 12″ / 4″ (30 cm / 10 cm) | |
Discharge Size | 2″ NPT | |
Solids Handling | 2″ (50 mm) spherical solids | |
Cord Length | 10′ (3 m) auto, 15′ (5 m) nonauto standard | |
Cord Type | UL listed, 3-wire neoprene cord and plug | |
Max Head | 21.5′ (6.6 m) | |
Max Flow Rate | 128 GPM (484 LPM) | |
Max Operating Temperature | 130 °F (54 °C) | |
Cooling | Oil filled | |
Motor Protection | Auto reset thermal overload (1 Ph) | |
Cap | Cast iron | |
Motor Housing | Cast iron | |
Pump Housing | Cast iron | |
Base | Cast iron or engineered plastic | |
Upper Bearing | Sleeve bearing | |
Lower Bearing | Sleeve bearing | |
Mechanical Seals | Carbon and ceramic | |
Impeller Type | Non-clogging vortex | |
Impeller | Engineered plastic with metal insert | |
Hardware | Stainless steel | |
Motor Shaft | AISI 1215 cold rolled steel | |
Gasket | Neoprene | |
|
model | seal | mode | volts | phase | amps | hp | hz | lbs | kg |
---|---|---|---|---|---|---|---|---|---|
M266/BN266 | Single | Auto | 115 | 1 | 10.4 | 1/2 | 60 | 41 | 19 |
N266 | Single | Non | 115 | 1 | 10.4 | 1/2 | 60 | 41 | 19 |
D266/BE266 | Single | Auto | 230 | 1 | 5.5 | 1/2 | 60 | 41 | 19 |
E266 | Single | Non | 230 | 1 | 5.5 | 1/2 | 60 | 41 | 19 |
H266 | Single | Auto | 200-208 | 1 | 6.2 | 1/2 | 60 | 41 | 19 |
I266 | Single | Non | 200-208 | 1 | 6.2 | 1/2 | 60 | 41 | 19 |
F266 | Single | Non | 230 | 3 | 2.6 | 1/2 | 60 | 40 | 18 |
G266 | Single | Non | 460 | 3 | 1.5 | 1/2 | 60 | 40 | 18 |
M267/BN267 | Single | Auto | 115 | 1 | 10.4 | 1/2 | 60 | 47.5 | 22 |
N267 | Single | Non | 115 | 1 | 10.4 | 1/2 | 60 | 47.5 | 22 |
D267/BE267 | Single | Auto | 230 | 1 | 5.5 | 1/2 | 60 | 47.5 | 22 |
E267 | Single | Non | 230 | 1 | 5.5 | 1/2 | 60 | 47.5 | 22 |
H267 | Single | Auto | 200-208 | 1 | 6.2 | 1/2 | 60 | 47.5 | 22 |
I267 | Single | Non | 200-208 | 1 | 6.2 | 1/2 | 60 | 47.5 | 22 |
J267 | Single | Non | 200-208 | 3 | 2.6 | 1/2 | 60 | 47.5 | 22 |
F267 | Single | Non | 230 | 3 | 2.6 | 1/2 | 60 | 47.5 | 22 |
G267 | Single | Non | 460 | 3 | 1.5 | 1/2 | 60 | 47.5 | 22 |
013225 Performance Curve, 260 Series: 60 Hz
Performance Chart, 260 Series: 60 Hz
Consult factory for special applications:
Tank Diameter | Gallons / Liters Pumped |
18” (46 cm) simplex | 8 gallons / 36 liters |
24” (60 cm) simplex | 15 gallons / 68 liters |
30” (76 cm) duplex | 22 gallons / 100 liters |
36” (91 cm) duplex | 33 gallons / 150 liters |
48” (122 cm) duplex | 60 gallons / 273 liters |
Notes
The sizing of effluent systems normally requires variable level float(s) controls and properly sized basins to achieve required pumping cycles or dosing timers with non-automatic pumps.
Reserve powered design.
For unusual conditions a reserve safety factor is engineered into the design of every Zoeller pump.
*May be used in those states where codes do not restrict solids size in effluent systems.
** See charts for UL and CSA listings.
Motor | 1/2 HP | |
Voltage | 115 – 460 V | |
Phase | 1 or 3 Ph | |
Hertz | 60 Hz | |
RPM | 1750 RPM | |
Type | Split phase or 3 phase | |
Insulation | Class B | |
Amps | 1.5 – 9.4 Amps | |
Operation | Automatic or nonautomatic | |
Auto On / Off Points | 12″ / 4″ (30 cm / 10 cm) | |
Discharge Size | 2″ NPT | |
Solids Handling | 2″ (50 mm) spherical solids | |
Cord Length | 10′ (3 m) auto, 15′ (5 m) nonauto standard | |
Cord Type | UL listed, 3-wire neoprene cord and plug | |
Max Head | 21.5′ (6.6 m) | |
Max Flow Rate | 128 GPM (484 LPM) | |
Max Operating Temperature | 130 °F (54 °C) | |
Cooling | Oil filled | |
Motor Protection | Auto reset thermal overload (1 Ph) | |
Cap | Cast iron | |
Motor Housing | Cast iron | |
Pump Housing | Cast iron | |
Base | Cast iron or engineered plastic | |
Upper Bearing | Sleeve bearing | |
Lower Bearing | Sleeve bearing | |
Mechanical Seals | Carbon and ceramic | |
Impeller Type | Non-clogging vortex | |
Impeller | Engineered plastic with metal insert | |
Hardware | Stainless steel | |
Motor Shaft | AISI 1215 cold rolled steel | |
Gasket | Neoprene | |
|
model | seal | mode | volts | phase | amps | hp | hz | lbs | kg |
---|---|---|---|---|---|---|---|---|---|
M266/BN266 | Single | Auto | 115 | 1 | 10.4 | 1/2 | 60 | 41 | 19 |
N266 | Single | Non | 115 | 1 | 10.4 | 1/2 | 60 | 41 | 19 |
D266/BE266 | Single | Auto | 230 | 1 | 5.5 | 1/2 | 60 | 41 | 19 |
E266 | Single | Non | 230 | 1 | 5.5 | 1/2 | 60 | 41 | 19 |
H266 | Single | Auto | 200-208 | 1 | 6.2 | 1/2 | 60 | 41 | 19 |
I266 | Single | Non | 200-208 | 1 | 6.2 | 1/2 | 60 | 41 | 19 |
F266 | Single | Non | 230 | 3 | 2.6 | 1/2 | 60 | 40 | 18 |
G266 | Single | Non | 460 | 3 | 1.5 | 1/2 | 60 | 40 | 18 |
M267/BN267 | Single | Auto | 115 | 1 | 10.4 | 1/2 | 60 | 47.5 | 22 |
N267 | Single | Non | 115 | 1 | 10.4 | 1/2 | 60 | 47.5 | 22 |
D267/BE267 | Single | Auto | 230 | 1 | 5.5 | 1/2 | 60 | 47.5 | 22 |
E267 | Single | Non | 230 | 1 | 5.5 | 1/2 | 60 | 47.5 | 22 |
H267 | Single | Auto | 200-208 | 1 | 6.2 | 1/2 | 60 | 47.5 | 22 |
I267 | Single | Non | 200-208 | 1 | 6.2 | 1/2 | 60 | 47.5 | 22 |
J267 | Single | Non | 200-208 | 3 | 2.6 | 1/2 | 60 | 47.5 | 22 |
F267 | Single | Non | 230 | 3 | 2.6 | 1/2 | 60 | 47.5 | 22 |
G267 | Single | Non | 460 | 3 | 1.5 | 1/2 | 60 | 47.5 | 22 |
013225 Performance Curve, 260 Series: 60 Hz
Performance Chart, 260 Series: 60 Hz