Zoeller's NEW Aquanot® Fit 508 Battery Backup System offers an economical option for dependable protection against basement flooding.

X

X400 Series Sewage Pumps

Hazardous Location Pumps // Sewage Pumps

X400 Series Sewage Pumps

Submersible effluent or dewatering pumps with explosion-proof motors.

Features and Benefits

  • FM listed motor for Class I, Division 1, Group C and D locations
  • Non-clogging vortex, cast iron impeller design
  • Stainless steel rotor shaft
  • Sensor leads and power leads in one cord for easy installation.
  • Durable, cast construction. Cast iron cover, motor adapter, impeller, and pump housing. No sheet metal parts to rust or corrode. All cast iron class 30, 30000# tensile strength
  • Stainless steel screws and handle
  • 20' (6 m), UL listed, 5-wire (1 Ph) or 8-wire (3 Ph) neoprene cord. Extra cord lengths available in 25', 35' and 50' (8, 11 and 15 m) lengths only.
  • 1-1/2" threaded conduit connection for protecting cords in extra heavy-duty applications
  • Moisture sensors pre-wired in motor housing (requires indicator in panel)
  • Zoeller control panels with intrinsically safe relays and moisture indicator are required
  • 3 Ph models available
  • Motor - 2 and 3 HP, 1750 RPM, oil-filled, hermetically-sealed, automatic reset thermal overload protected (3 Ph requires overload protection in control panel)
  • Maximum temperature for sewage or dewatering: 104 °F (40 °C)
  • Shaft seal: stainless steel wetted parts, carbon and ceramic rotary face seal
  • Upper ball bearing and lower ball bearing running in bath of oil
  • Buna-N square ring seals
  • Both models pass 3” (76 mm) spherical solids
  • Major width: 16-1/8" (41 cm)
  • Major height: 27-7/32" (69.1 cm)
  • Available in non-automatic units only
  • 4” horizontal flanged discharge, standard ANSI flanged
  • 100% computerized testing and 100% tested submerged in water
  • Corrosion-resistant, powder coated epoxy finish

Notes

The sizing of effluent systems normally requires variable level float(s) controls and properly sized basins to achieve required pumping cycles or dosing timers with non-automatic pumps.

Reserve powered design. For unusual conditions a reserve safety factor is engineered into the design of every Zoeller pump.

*See charts for FM listings.

Product Specifications

Motor 2 or 3 HP
Voltage 200 - 575 V
Phase 1 or 3 Ph
Hertz 60 Hz
RPM 1725 RPM
Type Permanent split capacitor or 3 phase
Insulation Class B
Amps 4.1 - 20.2 Amps
Operation Nonautomatic
Discharge Size 4" horizontal
Solids Handling 3" (76 mm) spherical solids
Cord Length 20' (6 m) standard
Cord Type UL listed, 5-wire (1 Ph) or 8-wire (3 Ph) SOOW cord
Max Head 38' (11.6 m)
Max Flow Rate 361 GPM (1367 LPM)
Max Operating Temperature 104 °F (40 °C)
Cooling Oil filled
Motor Protection Auto reset thermal overload (1 Ph) or thermal sensor (3 Ph)
Cap Cast iron
Motor Housing Cast iron
Pump Housing Cast iron
Base Cast iron
Upper Bearing Ball bearing
Lower Bearing Ball bearing
Mechanical Seals Carbon and ceramic with stainless steel parts
Impeller Type Non-clogging vortex
Impeller Cast iron
Hardware Stainless steel
Motor Shaft 416 stainless steel
  • Powder Coated Tough
  • SSPMA
  • CSA

Technical Data

Selection Guide

  1. See FM1705 for correct intrinsically-safe simplex or duplex panel.
  2. Variable level control switch 10-0225 used as a control activator, quantity required dependent upon panel selection, FM0526.

Caution

All installation of controls, protection devices and wiring should be done by a qualified licensed electrician. All electrical and safety codes should be followed including the most recent National Electric Code (NEC) and the Occupaitonal Safety and Health Act (OSHA).

Warning

Not for use in acidic, methanol or ethyl acetate atmospheres.

Model Comparison Charts

  • Product Model Comparison Chart: 60hz
    model seal mode volts phase amps hp hz lbs kg
    EX404 Single Non 230 1 12.9 2 60 175 79
    IX404 Single Non 200 1 14.4 2 60 175 79
    JX404 Single Non 200 3 13.8 2 60 175 79
    FX404 Single Non 230 3 10.5 2 60 175 79
    GX404 Single Non 460 3 5.2 2 60 175 79
    BAX404 Single Non 575 3 4.1 2 60 175 79
    EX405 Single Non 230 1 19.0 3 60 175 79
    IX405 Single Non 200 1 20.2 3 60 175 79
    JX405 Single Non 200 3 14.8 3 60 175 79
    FX405 Single Non 230 3 12.2 3 60 175 79
    GX405 Single Non 460 3 6.1 3 60 175 79
    BAX405 Single Non 575 3 4.8 3 60 175 79

Pump Performance Curves

Design Tools

Sales and Marketing