Register for upcoming webinars on our E-training page!

X

X180, X190 Series Effluent Pumps

Hazardous Location Pumps // Effluent Pumps // High Head Explosion Proof

X180, X190 Series Effluent Pumps

Submersible effluent or dewatering pumps with explosion-proof motors.

Features and Benefits

  • cCSAus rated Class I, Division 1, Groups C & D and Class Zone 1, Groups IIA & IIB Construction
  • Tested to FM standards 3600 and 3615 by CSA
  • Automatic or non-automatic. Automatic units Patent No. 8,535,014
  • Non-clogging vortex impeller design, bronze class 88-8-0-4
  • Stainless steel rotor shaft
  • Sensor leads and power leads in one cord for easy installation
  • Durable cast iron (class 30, 30000# tensile strength) constructed cover, motor adapter and pump housing
  • 1-1/4” NPT (nonauto), 1-1/2" NPT (auto): Threaded conduit connection for protecting cords in extra heavy duty applications
  • Stainless steel plate, bolts, handle, guard and float rod guide, switch arm and actuator assembly
  • Brass float and float rod (automatic only)
  • Moisture sensors pre-wired in motor housing (functionality requires indicator circuit in panel)
  • Zoeller control panel with intrinsically-safe relays and moisture indicator is required with non-automatic units.
  • Simplex seal-fail panel #10-1031 available for automatic units.
  • 3 Ph models available as non-automatic only
  • Oil-filled, hermetically-sealed motor, automatic reset thermal overload protected (3 Ph requires circuit in control panel)
  • Maximum temperature for effluent or dewatering: 104 °F (40 °C)
  • Shaft seal: stainless steel wetted parts, carbon and ceramic rotary face seal
  • Upper ball bearing and lower ball bearing running in bath of oil
  • Neoprene square ring seals
  • All X180 models pass 3/4” (19 mm) spherical solids
  • Model X191 pump passes 5/8” (15 mm) spherical solids
  • Major width: 13-5/16" (33.8 cm)
  • Major height: 22" (55.9 cm) (nonauto), 23-9/32" (59.1 cm) (auto)
  • On point: 19-1/2" (49.5 cm)
  • Off point: 9-3/4" (24.8 cm) (automatic)
  • Available in non-automatic units only
  • 1-1/2” NPT discharge standard, 2” and 3” NPT flange available
  • 100% submerged and computerized tested
  • Corrosion-resistant, powder-coated epoxy finish

Product Specifications

Motor 1 - 2 HP
Voltage 200 - 575 V
Phase 1 or 3 Ph
Hertz 60 Hz
RPM 3450 RPM
Type Permanent split capacitor or 3 phase
Insulation Class B
Amps 3.3 - 20.5 Amps
Operation Automatic or nonautomatic
Auto On / Off Points 19-1/2" / 9-3/4" (49.5 cm / 24.8 cm)
Discharge Size 1-1/2" NPT (optional 2" or 3" flange available)
Solids Handling 3/4" (19 mm) X180 series, 5/8" (15 mm) X190 series, spherical solids
Cord Length 20' (6 m) standard
Cord Type UL listed 5-wire (1 Ph) or 8-wire (3 Ph) SOOW cord
Max Head 137' (42 m)
Max Flow Rate 145 GPM (549 LPM)
Max Operating Temperature 104 °F (40 °C)
Cooling Oil filled
Motor Protection Auto reset thermal overload (1 Ph) or thermal sensor (3 Ph)
Cap Cast iron
Motor Housing Cast iron
Pump Housing Cast iron
Base Cast iron
Upper Bearing Ball bearing
Lower Bearing Ball bearing
Mechanical Seals Carbon and ceramic with stainless steel parts
Impeller Type Non-clogging vortex
Impeller Bronze
Hardware Stainless steel or brass
Motor Shaft 416 Stainless steel
  • Powder Coated Tough
  • SSPMA
  • CSA

Technical Data

Selection Guide

  1. See FM1705 for correct intrinsically safe simplex or duplex panel.
  2. Variable level control switch used as a control activator. Quantity required dependent upon panel selection.
  3. Integral operated mechanical switch. No external control required. Seal failure indicator panel (10-1031) required for moisture sensors.
  4. Automatic pumps: Use the seal failure panel (10-1031) to enable the moisture sensor circuit if required by local codes.

Model Comparison Charts

  • Product Model Comparison Chart: 60hz
    model seal mode volts phase amps hp hz lbs kg
    DX185 Single Auto 230 1 9.8 1 60 124 56
    EX185 Single Non 230 1 9.8 1 60 116 52
    HX185 Single Auto 200 1 11.5 1 60 124 56
    JX185 Single Non 200 1 11.5 1 60 119 53
    FX185 Single Non 230 3 7.4 1 60 119 53
    JX185 Single Non 200 3 7.5 1 60 119 53
    GX185 Single Non 460 3 3.7 1 60 119 53
    BAX185 Single Non 575 3 3.3 1 60 119 53
    DX186 Single Auto 230 1 13.7 1-1/2 60 128 58
    EX186 Single Non 230 1 13.7 1-1/2 60 126 57
    HX186 Single Auto 200 1 17.2 1-1/2 60 126 57
    IX186 Single Non 200 1 17.2 1-1/2 60 126 57
    FX186 Single Non 230 3 9.2 1-1/2 60 126 57
    JX186 Single Non 200 3 10.3 1-1/2 60 126 57
    GX186 Single Non 460 3 4.6 1-1/2 60 126 57
    DX188 Single Auto 230 1 14.0 1-1/2 60 128 58
    EX188 Single Non 230 1 14.0 1-1/2 60 126 57
    HX188 Single Auto 200 1 16.8 1-1/2 60 128 58
    IX188 Single Non 200 1 16.8 1-1/2 60 126 57
    FX188 Single Non 230 3 8.9 1-1/2 60 126 57
    JX188 Single Non 200 3 10.3 1-1/2 60 126 57
    GX188 Single Non 460 3 4.6 1-1/2 60 126 57
    BAX188 Single Non 575 3 3.5 1-1/2 60 126 57
    DX189 Single Auto 230 1 17.1 2 60 128 58
    EX189 Single Non 230 1 17.1 2 60 126 57
    HX189 Single Auto 200 1 20.5 2 60 128 58
    IX189 Single Non 200 1 20.5 2 60 126 57
    FX189 Single Non 230 3 11.2 2 60 126 57
    JX189 Single Non 200 3 13.2 2 60 126 57
    GX189 Single Non 460 3 6.0 2 60 126 57
    BAX189 Single Non 575 3 5.8 2 60 126 57
    DX191 Single Auto 230 1 14.5 2 60 128 58
    EX191 Single Non 230 1 14.5 2 60 129 58

Pump Performance Curves

Design Tools

Sales and Marketing

Sales Literature