Welcome to our NEW website!

X

180, 190 Series

img-title
Sump and Effluent Pumps // Commercial Use // High Head Flow-Mate

180, 190 Series

Effluent or dewatering submersible pump for septic tank, low pressure pipe (LPP) and enhanced flow STEP systems.

Features and Benefits

  • Non-clogging vortex impeller design, bronze class 88-8-0-4 (180 series)
  • Enclosed impeller design (model 191, 60 Hz only)
  • Float-operated, submersible, 2-pole mechanical switch
  • Durable, cast iron construction
  • Cast iron switch case, base, motor and pump housing
  • No sheet metal parts to rust or corrode
  • Stainless steel screws, bolts, float rod, handle, guard, arm and seal assembly
  • Oil-filled, hermetically-sealed, automatic reset thermal overload protection (1 Ph only)
  • Maximum temperature for effluent or dewatering: 130 °F (54 °C), WD189 (60 Hz): 120 °F (49 °C)
  • Variable level control systems available
  • Neoprene square ring and gasket
  • Stainless steel carbon and ceramic rotary shaft seal
  • SAE 1117 carbon steel motor shaft (single seal only)
  • Upper and lower ball bearing running in bath of oil
  • All 180/4180 series pumps pass 3/4” (19 mm) spherical solids.
  • Model 191 passes 5/8” (16 mm) spherical solids.
  • On point: 14-3/4” (37.5 cm)
  • Off point: 5-1/4” (12.7 cm)
  • Major width: 12-3/4" (32.4 cm) (single seal pumps)
  • Major height: 19-5/16" (49.1 cm) (single seal pumps)
  • 1-1/2” NPT discharge with 2” or 3” flange available
  • Model 191 not available with 3” flange
  • Corrosion-resistant, powder coated epoxy finish
  • Automatic units not recommended for use in effluent systems

Models 4185, 4186, 4188, 4189 Double Seal Pumps (60 Hz, non-automatic only):

  • Protects motor from seal leaks
  • Improved bearing lubrication
  • Helps eliminate seal and bearing damage from dry runs
  • 416 stainless steel motor shaft
  • Major width: 12-3/4" (32.4 cm)
  • Major height: 21-3/16" (53.8 cm)

Notes

Note: The sizing of effluent systems normally requires variable level float(s) controls and properly sized basins to achieve required pumping cycles or dosing timers with non-automatic pumps.

Note: No UL listing for 200/208 V, 1 Ph pumps, models 186 & 191, or double seal series. See charts for UL & CSA listings.

Reserve Powered Design.
For unusual conditions a reserve safety factor is engineered into the design of every Zoeller® pump.

Product Specifications

Motor 1 - 2 HP
Voltage 200 - 575 V
Phase 1 or 3 Ph
Hertz 60 Hz
RPM 3450 RPM
Type Permanent split capacitor or 3 Ph
Insulation Class B/185 & 4185, Class F/186-191 & 4186-4189
Amps 3.3 - 20.5 Amps
Operation Automatic or nonautomatic
Auto On / Off Points 15-3/4" (400 mm) / 5-1/4" (133 mm)
Discharge Size 1-1/2" NPT (optional 2" or 3" flange)
Solids Handling 180/4180: 3/4" (19 mm), 191: 5/8" (15 mm) spherical solids
Cord Length 20' (6 m) standard
Cord Type UL listed, 3-wire neoprene cord and plug (1 Ph) or 4-wire cord with no plug (3 Ph)
Max Head 137' (42 m)
Max Flow Rate 145 GPM (549 LPM)
Max Operating Temperature 130 °F (54 °C), (model WD189 120 °F [49 °C])
Cooling Oil filled
Motor Protection Auto reset thermal overload (1 Ph)
Cap Cast iron
Motor Housing Cast iron
Pump Housing Cast iron
Base Cast iron
Upper Bearing Ball bearing
Lower Bearing Ball bearing
Mechanical Seals Carbon and ceramic
Impeller Type Non-clogging vortex
Impeler Bronze
Hardware Stainless steel
Motor Shaft 1117 carbon steel or 416 stainless steel*
Gasket Neoprene
  • 60Hz
  • cCSAus
  • Powder Coated Tough
  • SSPMA
  • UL

Technical Data

CAUTION

All installation of controls, protection devices and wiring should be done by a qualified licensed electrician. All electrical and safety codes should be followed including the most recent National Electric Code (NEC) and the Occupational Safety and Health Act (OSHA).

Model 185 should not be subjected to heads less than 30' (10 m) TDH.

No UL listing for 200 V, 1 Ph pumps, models 186 & 191, or double seal series.

SELECTION GUIDE

  1. Integral float operated mechanical switch, no external control required.
  2. For automatic use single piggyback variable level float switch or double piggyback variable level float switch. Refer to FM0477.
  3. SeeFM1228 for correct model of simplex control panel.
  4. See FM0712 for correct model of duplex control panel.
  5. Variable level control switch 10-0743 used as a control activator, specify simplex (3) float or duplex (4) float system. Refer to FM0526.
  6. To select an appropriate basin, go to Basins.

* No Molded Plug (1) UL Listed unit available with 20 Amp Plug (2) CSA Approval without plug cap. (3) 20 Amp Outlet, P/N 10-0060 must be used.

ACCESSORIES

Model Comparison Charts

  • Product Model Comparison Chart: 60hz
    model seal mode volts phase amps hp hz lbs kg
    D185 / H185 Single Auto 230 / 200 1 9.8 / 11.5 1 60 85 / 86 38 / 39
    E185/E4185 Single / Double Non 230 1 9.8 1 60 85 / 92 38 / 41
    I185/I4185 Single / Double Non 200 1 11.5 1 60 85 / 92 38 / 41
    F185/F4185 Single / Double Non 230 3 7.4 1 60 85 / 92 38 / 41
    J185/J4185 Single / Double Non 200 3 7.5 1 60 85 / 92 38 / 41
    G185/G4185 Single / Double Non 460 3 3.7 1 60 85 / 92 38 / 41
    BA185 Single Non 575 3 3.3 1 60 85 38
    BE185 Single Auto 230 1 9.5 1 60 87 39
    D186 / H186 Single Auto 230 / 200 1 13.7 / 17.2 1-1/2 60 91 41
    E186/E4186 Single / Double Non 230 1 13.7 1-1/2 60 90 / 97 40 / 43
    I186/I4186 Single / Double Non 200 1 17.2 1-1/2 60 90 / 97 40 / 43
    F186/F4186 Single / Double Non 230 3 9.2 1-1/2 60 90 / 97 40 / 43
    J186/J4186 Single / Double Non 200 3 10.3 1-1/2 60 90 / 97 40 / 43
    G186/G4186 Single / Double Non 460 3 4.6 1-1/2 60 90 / 97 40 / 43
    BA186/BA4186 Single / Double Non 575 3 3.6 1-1/2 60 90/97 40/43
    BE186 Single Auto 230 1 13.7 1 1/2 60 92 42
    D188 / H188 Single Auto 230 / 200 1 14.0 / 16.8 1-1/2 60 91 41
    E188/E4188 Single / Double Non 230 1 14.0 1-1/2 60 90 / 97 40 / 43
    I188/I4188 Single / Double Non 200 1 16.8 1-1/2 60 90 / 97 40 / 43
    F188/F4188 Single / Double Non 230 3 8.9 1-1/2 60 90 / 97 40 / 43
    J188/J4188 Single / Double Non 200 3 10.3 1-1/2 60 90 40 / 43
    G188/G4188 Single / Double Non 460 3 4.6 1-1/2 60 95 / 97 43 / 43
    BA188 Single Non 575 3 3.5 1-1/2 60 90 40
    BE188 Single Auto 230 1 14.0 1 1/2 60 92 42
    D189 / H189 Single Auto 230 / 200 1 17.1 / 20.5 2 60 91 41
    E189/E4189 Single / Double Non 230 1 17.1 2 60 90 / 97 40 / 43
    I189/I4189 Single / Double Non 200 1 20.5 2 60 90 / 97 40 / 43
    F189/F4189 Single / Double Non 230 3 11.2 2 60 90 / 97 40 / 43
    J189/J4189 Single / Double Non 200 3 13.2 2 60 90 / 97 40 / 43
    G189/G4189 Single / Double Non 460 3 6.0 2 60 90 / 97 40 / 43
    BA189/BA4189 Single / Double Non 575 3 5.8 2 60 90/97 40/43
    WD189/4189 Single / Double Auto 230 1 17.1 2 60 93 / 100 42 / 45
    E191 Single Non 230 1 14.5 2 60 87 39

Pump Performance Curves

Design Tools