Welcome to our NEW website!

X

160 Series

img-title
Sump and Effluent Pumps // Commercial Use // High Head Flow-Mate

160 Series

Effluent or dewatering submersible pumps for septic tanks, low pressure pipe (LPP) and enhanced flow STEP systems.

Features and Benefits

  • Durable, cast iron constructed switch case, base, motor and pump housing
  • Cast iron Class 25-30 (25,000X tensile strength)
  • Impeller - bronze class 85-5-5-5
  • Corrosion-resistant, powder coated epoxy finish
  • Oil-filled, hermetically-sealed, automatic reset thermal overload protected (1 Ph only) motor
  • Upper and lower ball bearing running in bath of oil
  • Carbon and ceramic shaft seal
  • SAE 1117 carbon steel motor shaft (single seal models only)
  • Maximum temperature for effluent or dewatering: 130 °F (54 °C) (E/D: 140 °F / 60 °C)
  • Major width: 12-3/4" (32 cm)
  • Major height: 19-5/16" (49 cm)
  • No screens to clog
  • Neoprene square ring and gasket
  • Stainless steel screws, bolts, float rod, handle, guard, arm and seal assembly
  • Passes 3/4” (19 mm) spherical solids
  • 1-1/2” NPT discharge with 2” or 3” flange available
  • Automatic units available with float-operated, submersible, 2-pole mechanical switch
  • On: point 14-3/4” (37.5 cm)
  • Off: point 5” (12.7 cm)
  • 100% of units are computerized tested

Models 4161, 4163, 4165 double seal pumps available (60 Hz, non-automatic only):

  • Protects motor from seal leaks
  • Improved bearing lubrication
  • Helps eliminate seal and bearing damage from dry runs
  • 416 stainless steel motor shaft
  • Major width: 12-3/4” (32 cm)
  • Major height: 21-3/16” (53.8 cm)

Product Specifications

Motor 1/2 or 1 HP
Voltage 115 - 575 V
Phase 1 or 3 Ph
Hertz 60 Hz
RPM 3450 RPM
Type Permanent split capacitor or 3 phase
Insulation Class B
Amps 2.4 - 15.5 Amps
Operation Automatic and nonautomatic
Auto On / Off Points 15-3/4" / 5-1/4" (40 cm / 13.3 cm)
Discharge Size 1-1/2" NPT (optional 2" or 3" flange)
Solids Handling 3/4" (19 mm) spherical solids
Cord Length 20' (6 m) standard
Cord Type UL listed, 3-wire neoprene cord and plug (1 Ph) or 4-wire cord with no plug (3 Ph)
Max Head 86.5' (26 m)
Max Flow Rate 100 GPM (379 LPM)
Max Operating Temperature 130 °F (54 °C)
Cooling Oil filled
Motor Protection Auto reset thermal overload (1 Ph)
Cap Cast iron
Motor Housing Cast iron
Pump Housing Cast iron
Base Cast iron
Upper Bearing Ball bearing
Lower Bearing Ball bearing
Mechanical Seals Carbon and ceramic
Impeller Type Non-clogging vortex
Impeler Bronze
Hardware Stainless Steel
Motor Shaft SAE 1117 carbon steel or 416 stainless steel*
Gasket Neoprene square ring & gasket
  • UL
  • 60Hz
  • cCSAus
  • SSPMA
  • Powder Coated Tough

Technical Data

CAUTION

All installation of controls, protection devices and wiring should be done by a qualified licensed electrician. All electrical and safety codes should be followed including the most recent National Electric Code (NEC) and the Occupational Safety and Health Act (OSHA).

SELECTION GUIDE

  1. Integral float operated mechanical switch, no external control required.
  2. For automatic use, single piggyback variable level float switch or double piggyback variable level float switch. Refer to FM0477.
  3. See FM1228 for correct model of simplex control panel.
  4. See FM0712 for correct model of duplex control panel.
  5. To select an appropriate basin, go to Basins.

ACCESSORIES

Model Comparison Charts

  • Product Model Comparison Chart: 60hz
    model seal mode volts phase amps hp hz lbs kg
    M161 Single Auto 115 1 15.5 1/2 60 80 36
    N161 / N4161 Single / Double Non 115 1 15.0 / 15.5 1/2 60 80 / 87 36 / 39
    BN161 Single Auto 115 1 15.0 1/2 60 84 38
    D161 Single Auto 230 1 7.5 1/2 60 80 36
    E161 / E4161 Single / Double Non 230 1 7.5 1/2 60 80 / 87 36 / 39
    H161 Single Auto 200 1 8.8 1/2 60 80 36
    I161 / I4161 Single / Double Non 200 1 8.8 1/2 60 80 / 87 36 / 39
    J161 / J4161 Single / Double Non 200 3 6.4 1/2 60 80 / 87 36 / 39
    F161 / F4161 Single / Double Non 230 3 5.2 1/2 60 80 / 87 36 / 39
    G161 / G4161 Single / Double Non 460 3 2.9 1/2 60 80 / 87 36 / 39
    BA161/BA4161 Single / Double Non 575 3 2.4 1/2 60 80 / 87 36 / 39
    BE161 Single Auto 230 1 15.0 1/2 60 84 38
    M163 Single Auto 115 1 15.0 1/2 60 80 36
    N163 / N4163 Single / Double Non 115 1 15.0 1/2 60 80 / 87 36 / 39
    BN163 Single Auto 115 1 15.0 1/2 60 84 38
    D163 Single Auto 230 1 7.5 1/2 60 80 36
    E163 / E4163 Single / Double Non 230 1 7.5 1/2 60 80 / 87 36 / 39
    F163 / F4163 Single / Double Non 230 3 4.8 1/2 60 80 / 87 36 / 39
    H163 Single Auto 200 1 8.5 1/2 60 80 36
    I163 / I4163 Single / Double Non 200 1 8.5 1/2 60 80 / 87 36 / 39
    J163 / J4163 Single / Double Non 200 3 6.0 1/2 60 80 / 87 36 / 39
    G163 / G4163 Single / Double Non 460 3 2.9 1/2 60 80 / 87 36 / 39
    BA163/BA4163 Single / Double Non 575 3 2.4 1/2 60 80 / 87 36 / 39
    BE163 Single Auto 230 1 7.5 1/2 60 84 38
    D165 Single Auto 230 1 10.2 1 60 80 36
    E165 / E4165 Single / Double Non 230 1 10.2 1 60 80 / 87 36 / 39
    H165 Single Auto 200 1 12.6 1 60 80 36
    I165 / I4165 Single / Double Non 200 1 12.6 1 60 80 / 87 36 / 39
    J165 / J4165 Single / Double Non 200 3 7.5 1 60 80 / 87 36 / 39
    F165 / F4165 Single / Double Non 230 3 7.4 1 60 80 / 87 36 / 39
    G165 / G4165 Single / Double Non 460 3 3.7 1 60 80 / 87 36 / 39
    BA165/BA4165 Single / Double Non 575 3 3.0 1 60 80 / 87 36 / 39
    BE165 Single Auto 230 1 10.2 1 60 84 38

Pump Performance Curves

Design Tools