Zoeller Pump Company has partnered with Contractor Rewards to offer you rewards for your Zoeller Pump purchases!


260 Series Sewage Pumps

Sewage Pumps // Residential Use Sewage Pumps // Waste-Mate

260 Series Sewage Pumps

Submersible sewage, effluent or dewatering pump

Features and Benefits

  • Float-operated, 2-pole mechanical switch
  • Durable cast construction, ASTM Class 25 cast iron switch case and pump housing
  • Cast iron base on model 267 
  • Engineered plastic base on model 266
  • Non-clogging vortex impeller design. Engineered plastic impeller with metal inserts (1 Ph). Model 267 available with cast iron impeller (standard on 3 Ph models).
  • Not affected by materials normally found in drainage and sewage pumps
  • Stainless steel screws, bolts, handle, guard and arm and seal assembly
  • Neoprene square ring and gasket
  • Oil-filled, hermetically-sealed motor
  • Oil-lubricated bearings
  • Carbon and ceramic shaft seal
  • Passes 2” (50 mm) spherical solids
  • 2” female discharge
  • On point: 12” (30 cm) (automatic units)
  • Off point: 4” (10 cm) (automatic units)
  • Corrosion-resistant, powder coated epoxy finish
  • Completely submersible
  • Watertight and dust-tight
  • Automatic and non-automatic models available
  • Models available packaged with a piggyback variable level float switch
  • Automatic reset thermal overload protection (1 Ph only)

Consult factory for special applications:

  • Minimum recommended basin size (small load applications): simplex 18” x 30” (45.7 x 76.2 cm), duplex 30” x 36” (76.2 x 91.4 cm)
  • High water alarms available
  • Standard 266 model: 41 lbs (19 kg)
  • Standard 267 model: 47.5 lbs (21.5 kg)
  • Approximate gallons pumped out per cycle for standard models:

Tank Diameter

Gallons / Liters Pumped

18” (45.7 cm) simplex

8 gallons / 36 liters

24” (61 cm) simplex

15 gallons / 68 liters

30” (76 cm) duplex

22 gallons / 100 liters

36” (76 cm) duplex

33 gallons / 150 liters

48” (122 cm) duplex

60 gallons / 273 liters

* May be used in those states where codes do not restrict solids size in effluent systems.

** See charts for UL and CSA listings.

The sizing of effluent systems normally requires variable level float(s) controls and properly sized basins to achieve required pumping cycles or dosing timers with non-automatic pumps.

Reserve powered design.

For unusual conditions a reserve safety factor is engineered into the design of every Zoeller® pump.

Product Specifications

Motor 1/2 HP
Voltage 115 - 460 V
Phase 1 or 3 Ph
Hertz 60 Hz
RPM 1750 RPM
Type Split phase or 3 phase
Insulation Class B
Amps 1.5 - 10.4 Amps
Operation Automatic or nonautomatic
Auto On / Off Points 12" / 4" (30 cm / 10 cm)
Discharge Size 2" or 3" NPT
Solids Handling 2" (50 mm) spherical solids
Cord Length 10' (3 m) auto, 15' (5 m) nonauto standard
Cord Type UL listed, 3-wire neoprene cord and plug
Max Head 21.5' (6.6 m)
Max Flow Rate 128 GPM (484 LPM)
Max Operating Temperature 130 °F (54 °C)
Cooling Oil filled
Motor Protection Auto reset thermal overload (1 Ph)
Cap Cast iron
Motor Housing Cast iron
Pump Housing Cast iron
Base Cast iron or engineered plastic
Upper Bearing Sleeve bearing
Lower Bearing Sleeve bearing
Mechanical Seals Carbon and ceramic
Impeller Type Non-clogging vortex
Impeller Engineered plastic with metal insert
Hardware Stainless steel
Motor Shaft AISI 1215 cold rolled steel
Gasket Neoprene
  • 60Hz
  • cCSAus
  • Powder Coated Tough

Technical Data


All installation of controls, protection devices and wiring should be done by a qualified licensed electrician. All electrical and safety codes should be followed including the most recent National Electric Code (NEC) and the Occupational Safety and Health Act (OSHA).

Maximum temperature of sewage or dewatering must be limited to 130°F (54°C). For over 130°F (54°C) special quotation required.

Selection Guide

  1. Integral float operated mechanical switch, no external control required.
  2. For automatic use single piggyback variable level float switch or double piggyback variable level float switch. Refer to FM0477.
  3. See FM1228 for correct model of simplex control panel.
  4. See FM0712 for correct model of duplex control panel or FM1663 for a residential alternator system.


Pump Performance Curves

Design Tools

Sales and Marketing

Sales Literature