Welcome to our NEW website!

X

600 Series

img-title
Sewage Pumps // Commercial Use // Sewage-Waste

600 Series

Submersible sewage or dewatering non-clog pumps.

Features and Benefits

  • Model 611: 1 HP, Model 621: 1.5 HP, Model 631: 2 HP, Model 641: 3 HP, Model 651: 5 HP, Model 661: 7.5 HP
  • Class 30 cast iron construction
  • All units are double seal for extra motor protection
  • Corrosion-resistant, powder coated epoxy finish
  • Stainless steel screws, washers, tag and seal assembly
  • 1 Ph – capacitor start, capacitor run
  • Oil-filled, hermetically-sealed motor with heavy-duty, finned motor housing for added heat dissipation
  • Continuous duty operation in submerged conditions
  • Maximum temperature for sewage or dewatering: 104 °F (40 °C) with 1.2 service factor (1.0 service factor on model 661)
  • 416 stainless steel motor shaft
  • Stainless steel fitted tandem shaft seals, carbon/ceramic seal faces
  • Over-sized upper and lower ball bearings running in an oil bath
  • Buna N square rings and seals used throughout
  • All models pass 2-1/2” (63 mm) spherical solids
  • Specify 3” NPT vertical, 3” horizontal flanged or 4” horizontal flanged discharge
  • 100% computerized tested
  • Major width: 17-9/16" (44.6 cm)
  • Major height: 29-1/4" (74.3 cm)
  • Rail systems available for all models
  • Control panels with overload protection available
  • Non-automatic for variable level control systems
  • Double seal only
  • Patent No. 6,364,620

Notes

The sizing of effluent systems normally requires variable level float(s) controls and properly sized basins to achieve required pumping cycles or dosing timers with non-automatic pumps.

Reserve powered design.
For unusual conditions a reserve safety factor is engineered into the design of every Zoeller pump.

Product Specifications

Motor 1 - 7.5 HP
Voltage 200 - 575 V
Phase 1 or 3 Ph
Hertz 60 Hz
RPM 1750 RPM
Type Capacitor start capacitor run or 3 phase
Insulation Class F
Amps 1.6 - 28.0 Amps
Operation Nonautomatic
Discharge Size 3" NPT (optional 3" or 4" flange available)
Solids Handling 2-1/2" (63 mm) spherical solids
Cord Length 25' (8 m) standard
Cord Type UL listed 3-wire cord
Max Head 65' (19.8 m)
Max Flow Rate 533 GPM (2018 LPM)
Max Operating Temperature 104 °F (40 °C)
Cooling Oil filled
Motor Protection Auto reset thermal overload (1 Ph)
Cap Cast iron
Motor Housing Cast iron
Pump Housing Cast iron
Base Cast iron
Upper Bearing Ball bearing
Lower Bearing Ball bearing
Mechanical Seals Tandem carbon and ceramic
Impeller Type Semi-open
Impeler Ductile iron
Hardware Stainless steel
Motor Shaft Stainless steel
Gasket Buna N O-Ring
  • 60Hz
  • cCSAus
  • Powder Coated Tough
  • SSPMA

Technical Data

CAUTION

All installation of controls, protection devices and wiring should be done by a qualified licensed electrician. All electrical and safety codes should be followed including the most recent National Electric Code (NEC) and the Occupational Safety and Health Act (OSHA).

ACCESSORIES

Model Comparison Charts

  • Product Model Comparison Chart: 60hz
    model seal mode volts phase amps hp hz lbs kg
    E611 Double Non 230 1 6.9 1 60 245 111
    J611 Double Non 200 3 4.8 1 60 245 111
    F611 Double Non 230 3 4.2 1 60 245 111
    G611 Double Non 460 3 2.1 1 60 245 111
    BA611 Double Non 575 3 1.7 1 60 245 111
    E621 Double Non 230 1 8.9 1-1/2 60 245 111
    J621 Double Non 200 3 5.9 1-1/2 60 245 111
    F621 Double Non 230 3 5.1 1-1/2 60 245 111
    G621 Double Non 460 3 2.6 1-1/2 60 245 111
    BA621 Double Non 575 3 2.0 1-1/2 60 245 111
    E631 Double Non 230 1 14.5 2 60 245 111
    J631 Double Non 200 3 7.8 2 60 245 111
    F631 Double Non 230 3 6.8 2 60 245 111
    G631 Double Non 460 3 3.4 2 60 245 111
    BA631 Double Non 575 3 2.7 2 60 245 111
    E641 Double Non 230 1 17.0 3 60 245 111
    J641 Double Non 200 3 11.0 3 60 245 111
    F641 Double Non 230 3 9.6 3 60 245 111
    G641 Double Non 460 3 4.8 3 60 245 111
    BA641 Double Non 575 3 3.9 3 60 245 111
    E651 Double Non 230 1 28.0 5 60 245 111
    J651 Double Non 200 3 17.5 5 60 245 111
    F651 Double Non 230 3 15.2 5 60 245 111
    G651 Double Non 460 3 7.6 5 60 245 111
    BA651 Double Non 575 3 6.1 5 60 245 111
    J661 Double Non 200 3 25.3 7-1/2 60 245 111
    F661 Double Non 230 3 22.0 7-1/2 60 245 111
    G661 Double Non 460 3 11.0 7-1/2 60 245 111
    BA661 Double Non 575 3 9.0 7-1/2 60 245 111

Pump Performance Curves

Design Tools