Welcome to our NEW website!

X

400 Series

img-title
Sewage Pumps // Commercial Use // Waste-Mate

400 Series

Single and double seal submersible sewage or dewatering pumps.

Features and Benefits

  • Cast iron casting, class 25-30 25000# tensile strength
  • Oil-filled, hermetically-sealed, automatic reset thermal overload protected (1 Ph only) motor
  • Upper and lower ball bearing running in bath of oil
  • Mechanical shaft seal - carbon and ceramic rotary face seal, with stainless steel wetted parts
  • 1117 carbon steel motor shaft (single seal models)
  • Stainless steel screws, bolts, washers and lifting bracket
  • Neoprene square ring and gasket
  • Maximum temperature: 130 °F (54 °C) standard
  • Variable level controls available
  • 4” horizontal flanged discharge, standard ANSI flange
  • Passes 3” (76 mm) spherical solids
  • Corrosion-resistant, powder coated epoxy finish
  • Non-automatic available
  • Applications include:
    • High capacity water removal - parking lots, low flood areas, water transfer
    • To meet 3" intake, 4" discharge code requirements on some sewage applications
    • Retrofit on existing sewage installations
    • New installations

Model 4404, 4405 double seal pumps (non-automatic):

  • Protects motor from seal leaks
  • Improved seal lubrication
  • Helps eliminate seal and bearing damage from dry runs
  • 416 stainless steel motor shaft
  • Major width: 16-1/8” (41 cm)
  • Major height: 2-1/2” (69.9 cm)

Guide rail systems:

  • 4” (DN100) pipe flange fittings
  • P/N 39-0016
  • Includes:
    • Cast iron discharge elbow
    • Stainless steel lower guides
    • Cast iron mounting plate
    • Stainless steel upper guide rail bracket
    • Optional intermediate stabilizer for systems over 15’ (5 m) deep (P/N 39-0013 carbon steel, P/N 39-0014 stainless steel)
    • Stainless steel guide brackets for pump mounting plate
    • Buna N gasket for mounting plate
    • Stainless steel bolts and lock washers
    • Features automatic engagement, easy disengagement and class 30 cast iron fittings
    • Uses 2” IPs guide rails and pull cable or chain (not furnished)

Consult factory for special applications:

  • Electrical alternators, for duplex systems
  • Mechanical alternators, for duplex systems (with or without high-water alarm functions)
  • Simplex control panels available
  • Variable level float switches are available for controlling single and three phase systems
  • Double piggyback float switches are available for variable level long cycle controls
  • Long cords available in lengths of 25' (8 m), 35’ (11 m) and 50’ (15 m)
  • Simplex and duplex basins available

Notes 
The sizing of effluent systems normally requires variable level float(s) controls and properly sized basins to achieve required pumping cycles or dosing timers with non-automatic pumps.

Reserve powered design.

For unusual conditions a reserve safety factor is engineered into the design of every Zoeller pump.

Product Specifications

Motor 2 or 3 HP
Voltage 200 - 575 V
Phase 1 or 3 Ph
Hertz 60 Hz
RPM 1725 RPM
Type Permanent split capacitor or 3 phase
Insulation Class B
Amps 4.1 - 20.2 Amps
Operation Automatic and nonautomatic
Discharge Size 4" horizontal ANSI flange
Solids Handling 3" (76 mm) spherical solids
Cord Length 20' (6 m) standard
Cord Type UL listed, 3-wire neoprene cord and plug
Max Head 38' (11.6 m)
Max Flow Rate 361 GPM (1367 LPM)
Max Operating Temperature 130 °F (54 °C)
Cooling Oil filled
Motor Protection Auto reset thermal overload (1 Ph)
Cap Cast iron
Motor Housing Cast iron
Pump Housing Cast iron
Base Cast iron
Upper Bearing Ball bearing
Lower Bearing Ball bearing
Mechanical Seals Carbon and ceramic
Impeller Type Non-clogging vortex
Impeler Cast iron
Hardware Stainless steel
Motor Shaft 1117 carbon steel or 416 stainless steel*
Gasket Neoprene
  • 60Hz
  • cCSAus
  • SSPMA
  • Powder Coated Tough

Technical Data

CAUTION

All installation of controls, protection devices and wiring should be done by a qualified licensed electrician. All electrical and safety codes should be followed including the most recent National Electric Code (NEC) and the Occupational Safety and Health Act (OSHA).

SELECTION GUIDE

  1. For automatic use single piggyback variable level float switch or double piggyback variable level float switch. Refer to FM0477.
  2. See FM1228 for correct model of simplex control panel.
  3. See FM0712 for correct model of duplex control panel.

20 amp outlet P/N 10-0060, must be used with model E405/4404 and WD405/4405.

ACCESSORIES

Model Comparison Charts

  • Product Model Comparison Chart: 60hz
    model seal mode volts phase amps hp hz lbs kg
    E404 Single Non 230 1 12.9 2 60 136 61
    E4404 Double Non 230 1 12.9 2 60 147 66
    WD404 Single Auto 230 1 12.9 2 60 139 63
    WD4404 Double Auto 230 1 12.9 2 60 150 68
    I404 Single Non 200 1 14.4 2 60 136 61
    I4404 Double Non 200 1 14.4 2 60 147 66
    J404 Single Non 200 3 13.8 2 60 136 61
    J4404 Double Non 200 3 13.8 2 60 147 66
    F404 Single Non 230 3 10.5 2 60 136 61
    F4404 Double Non 230 3 10.5 2 60 147 66
    G404 Single Non 460 3 5.2 2 60 136 61
    G4404 Double Non 460 3 5.2 2 60 147 66
    BA404 Single Non 575 3 4.1 2 60 136 61
    BA4404 Double Non 575 3 4.1 2 60 147 66
    E405 Single Non 230 1 19.0 3 60 136 61
    E4405 Double Non 230 1 19.0 3 60 147 66
    WD405 Single Auto 230 1 19.0 3 60 139 63
    ED4405 Double Auto 230 1 19.0 3 60 150 68
    I405 Single Non 200 1 20.2 3 60 136 61
    I4405 Double Non 200 1 20.2 3 60 145 65
    J405 Single Non 200 3 14.8 3 60 136 61
    J4405 Double Non 200 3 14.8 3 60 147 66
    F405 Single Non 230 3 12.2 3 60 136 61
    F4405 Double Non 230 3 12.2 3 60 147 66
    G405 Single Non 460 3 6.1 3 60 136 61
    G4405 Double Non 460 3 6.1 3 60 147 66
    BA405 Single Non 575 3 4.8 3 60 136 61
    BA4405 Double Non 575 3 4.8 3 60 146 66

Pump Performance Curves

Design Tools