Welcome to our NEW website!

X

260 Series

img-title
Sewage Pumps // Residential Use // Waste-Mate

260 Series

Submersible sewage, effluent or dewatering pump

Features and Benefits

  • Float-operated, 2-pole mechanical switch
  • Durable cast construction, ASTM Class 25 cast iron switch case and pump housing
  • Cast iron base on model 267 
  • Engineered plastic base on model 266
  • Non-clogging vortex impeller design. Engineered plastic impeller with metal inserts (1 Ph). Model 267 available with cast iron impeller (standard on 3 Ph models).
  • Not affected by materials normally found in drainage and sewage pumps
  • Stainless steel screws, bolts, handle, guard and arm and seal assembly
  • Neoprene square ring and gasket
  • Oil-filled, hermetically-sealed motor
  • Oil-lubricated bearings
  • Carbon and ceramic shaft seal
  • Passes 2” (50 mm) spherical solids
  • 2” female and 3" NPT male discharge
  • On point: 12” (30 cm) (automatic units)
  • Off point: 4” (10 cm) (automatic units)
  • Corrosion-resistant, powder coated epoxy finish
  • Completely submersible
  • Watertight and dust-tight
  • Automatic and non-automatic models available
  • Models available packaged with a piggyback variable level float switch
  • Automatic reset thermal overload protection (1 Ph only)

Consult factory for special applications:

  • Minimum recommended basin size (small load applications): simplex 18” x 30” (45.7 x 76.2 cm), duplex 30” x 36” (76.2 x 91.4 cm)
  • High water alarms available
  • Standard 266 model: 41 lbs (19 kg)
  • Standard 267 model: 47.5 lbs (21.5 kg)
  • Approximate gallons pumped out per cycle for standard models:

Tank Diameter

Gallons / Liters Pumped

18” (45.7 cm) simplex

8 gallons / 36 liters

24” (61 cm) simplex

15 gallons / 68 liters

30” (76 cm) duplex

22 gallons / 100 liters

36” (76 cm) duplex

33 gallons / 150 liters

48” (122 cm) duplex

60 gallons / 273 liters

* May be used in those states where codes do not restrict solids size in effluent systems.

** See charts for UL and CSA listings.

Notes 
The sizing of effluent systems normally requires variable level float(s) controls and properly sized basins to achieve required pumping cycles or dosing timers with non-automatic pumps.

Reserve powered design.

For unusual conditions a reserve safety factor is engineered into the design of every Zoeller® pump.

Product Specifications

60hz 50hz
Motor 1/2 HP 0.7 kW
Voltage 115 - 460 V 220 V
Phase 1 or 3 Ph 1 Ph
Hertz 60 Hz 50 Hz
RPM 1750 RPM 1400 RPM
Type Split phase or 3 phase Split phase
Insulation Class B Class B
Amps 1.5 - 10.4 Amps 4.4 A
Operation Automatic or nonautomatic Automatic or nonautomatic
Auto On / Off Points 12" / 4" (30 cm / 10 cm) 30.4 cm / 10.1 cm (12" / 4")
Discharge Size 2" or 3" NPT 2" NPT (CE models with BSPT)
Solids Handling 2" (50 mm) spherical solids 50 mm (2") spherical solids
Cord Length 10' (3 m) auto, 15' (5 m) nonauto standard 3 m (9') auto, 5 m (15') nonauto
Cord Type UL listed, 3-wire neoprene cord and plug SOW/SOOW (CE model H07RN-F)
Max Head 21.5' (6.6 m) 4.3 m (14.0')
Max Flow Rate 128 GPM (484 LPM) 20.9 m3/hr (92 GPM)
Max Operating Temperature 130 °F (54 °C) 54 °C (130 °F)
Cooling Oil filled Oil filled
Motor Protection Auto reset thermal overload (1 Ph) Auto reset thermal overload
Cap Cast iron Cast iron
Motor Housing Cast iron Cast iron
Pump Housing Cast iron Cast iron
Base Cast iron or engineered plastic Cast iron or engineered plastic
Upper Bearing Sleeve bearing Sleeve bearing
Lower Bearing Sleeve bearing Sleeve bearing
Mechanical Seals Carbon and ceramic Carbon and ceramic
Impeller Type Non-clogging vortex Non-clogging vortex
Impeler Engineered plastic with metal insert Engineered plastic with metal inserts
Hardware Stainless steel Stainless steel
Motor Shaft AISI 1215 cold rolled steel AISI 1215 cold roll steel
Gasket Neoprene Neoprene
  • Cert 60Hz
  • Cert Sa
  • Cert Sspma
  • Cert Tough
  • 50Hz
  • Ce
  • Cert Tough

Technical Data

CAUTION

All installation of controls, protection devices and wiring should be done by a qualified licensed electrician. All electrical and safety codes should be followed including the most recent National Electric Code (NEC) and the Occupational Safety and Health Act (OSHA).
Maximum temperature of sewage or dewatering must be limited to 130°F (54°C). For over 130°F (54°C) special quotation required.

SELECTION GUIDE

  1. Integral float operated mechanical switch, no external control required.
  2. For automatic use single piggyback variable level float switch or double piggyback variable level float switch. Refer to FM0477.
  3. See FM1228 for correct model of simplex control panel.
  4. See FM0712 for correct model of duplex control panel or FM1663for a residential alternator system.

ACCESSORIES

Model Comparison Charts

  • Product Model Comparison Chart: 60hz
    model seal mode volts phase amps hp hz lbs kg
    M266/BN266 Single Auto 115 0 10.4 1/2 60 41 19
    N266 Single Non 115 0 10.4 12 60 41 19
    D266/BE266 Single Auto 230 0 5.5 1/2 60 41 19
    E266 Single Non 230 0 5.5 1/2 60 41 19
    H266 Single Auto 200-208 0 6.2 1/2 60 41 19
    I266 Single Auto 200-208 0 6.2 1/2 60 41 19
    J266 Single Non 200-208 3 2.6 1/2 60 41 19
    F266 Single Non 230 3 2.6 1/2 60 40 18
    G266 Single Non 460 3 1.5 1/2 60 40 18
    M267/BN267 Single Auto 115 0 10.4 1/2 60 47.5 22
    N267 Single Non 115 0 10.4 1/2 60 47.5 22
    D267/BE267 Single Auto 230 0 5.5 1/2 60 47.4 22
    E267 Single Non 230 0 5.5 1/2 60 47.5 22
    H267 Single Auto 200-208 0 6.2 1/2 60 47.5 22
    I267 Single Non 200-208 0 6.2 1/2 60 47.5 22
    J267 Single Non 200-208 3 2.6 1/2 60 47.5 22
    F267 Single Non 230 3 2.6 1/2 60 47.5 22
    G267 Single Non 460 3 1.5 1/2 60 47.5 22
  • Product Model Comparison Chart: 50hz
    model seal mode volts phase amps kw hz lbs kg
    U266 Single Auto 220 0 4.4 0.7 50 42 19
    V266 Single Non 220 0 4.4 0.7 50 42 19
    U267 Single Auto 220 0 4.4 0.7 50 49 22
    V267 Single Non 220 0 4.4 0.7 50 49 22
    U268 Single Auto 220 0 4.4 0.7 50 51 23
    V268 Single Non 220 0 4.4 0.7 50 51 23

Pump Performance Curves

Design Tools