280 Series Sewage Pumps

Sewage Pumps // Commercial Use Sewage Pumps // Waste-Mate

280 Series Sewage Pumps

Single and double seal submersible sewage or dewatering pumps

Features and Benefits

  • Durable, cast iron constructed switch case, motor and pump housing, base and impeller
  • No sheet metal parts to rust or corrode
  • All cast iron class 30 30000# tensile strength
  • Stainless steel screws, bolts, float rod, handle, guard and arm and seal assembly
  • Shaft seal - Carbon and ceramic rotary face seal, with stainless steel wetted parts
  • SAE 1117 carbon steel motor shaft (single seal models)
  • Upper and lower ball bearing running in bath of oil
  • Maximum temperature for sewage or dewatering: 130 °F (54 °C)
  • Oil-filled, hermetically-sealed, automatic reset thermal overload protected motor (1 Ph and auto 3 Ph)
  • All models available in 2” or 3” discharge
  • All models pass 2” (50 mm) spherical solids.
  • Automatic units available with float-operated, submersible mechanical switch**
  • Corrosion-resistant, powder coated epoxy finish
  • On point: 15-1/4” (38.7 cm)
  • Off point: 5-1/4” (13 cm)
  • Major width: 13-9/16” (34.4 cm) (single seal pumps)
  • Major height: 19-9/16” (49.7 cm) (single seal pumps)
  • Automatic or non-automatic with single seal
  • Non-automatic with double seals
  • 1 or 3 Ph motors available
  • See selection chart for specifications or specific models
  • 1 year limited warranty

Models 282, 4282 double seal pumps (non-automatic only)

  • Protects motor from leaks
  • Improved bearing lubrication
  • Helps eliminate seal and bearing damage from dry runs
  • 416 stainless steel motor shaft
  • Major width: 13-9/16" (34.4 cm)
  • Major height: 20-11/16" (52.5 cm)

Consult factory for special applications:

  • Three phase pumps are available in 200 V, 230 V, 460 V, or 575 V. 230 V three phase is available in automatic and non-automatic models.
  • Electrical alternators, for duplex systems, are available and supplied with a high water alarm, refer to FM0486.
  • Simplex Panel with high water alarm, refer to FM1596.
  • Variable level control switches are available for controlling 1 and 3 Ph systems
  • Double piggyback, variable level float switches are available for variable level long cycle controls
  • Longer cords are available in lengths of 25’ (8 m), 35’ (11 m) or 50’ (15 m)
  • Simplex and duplex basins are available
  • Refer to FM1922 and FM0806 for temperatures over 130 °F (54 °C)

Notes
The sizing of effluent systems normally requires variable level float(s) controls and properly sized basins to achieve required pumping cycles or dosing timers with non-automatic pumps.

Reserve powered design.

For unusual conditions a reserve safety factor is engineered into the design of every Zoeller® pump.

* No UL Listing or CSA Certification for 200 V 1 Ph or Extra Duty (ED) pumps.

** Three phase automatic units available in single seal only.

Product Specifications


60hz 50hz
Motor 1/2 or 1 HP 0.8 or 1.0 kW
Voltage 115 - 575 V 220 or 380 V
Phase 1 or 3 Ph 1 or 3 Ph
Hertz 60 Hz 50 Hz
RPM 1725 RPM 1400 RPM
Type Permanent split capacitor or 3 Ph Permanent split capacitor or 3 Ph
Insulation Class B Class B
Amps 1.4 - 10.3 Amps 1.6 - 5.7 A
Operation Automatic or nonautomatic Automatic or nonautomatic
Auto On / Off Points 16-1/2" / 5-1/4" (41.9 cm / 13.3 cm) 41.9 cm / 13.3 cm (16-1/2" / 5-1/4")
Discharge Size 2" or 3" NPT female, flanged vertical 2" NPT (optional 3" flange) (CE models with BSPT)
Solids Handling 2" (50 mm) spherical solids 50 mm (2") spherical solids
Cord Length 10' (3 m) auto, 15' (5 m) nonauto standard 3 m (10') auto, 5 m (15') nonauto standard
Cord Type UL listed, 3-wire neoprene cord and plug SOW/SOOW (CE model H07RN-F)
Max Head 35' (10.7 m) 7 m (23')
Max Flow Rate 179 GPM (678 LPM) 28.6 m3/hr (125.2 GPM)
Max Operating Temperature 130 °F (54 °C) 54 °C (130 °F)
Cooling Oil filled Oil filled
Motor Protection Auto reset thermal overload (1 Ph) Auto reset thermal overload (1 Ph)
Cap Cast iron Cast iron
Motor Housing Cast iron Cast iron
Pump Housing Cast iron Cast iron
Base Cast iron Cast iron
Upper Bearing Ball bearing Ball bearing
Lower Bearing Ball bearing Ball bearing
Mechanical Seals Carbon and ceramic Carbon and ceramic
Impeller Type Non-clogging vortex Non-clogging vortex
Impeller Cast iron Cast iron
Hardware Stainless steel Stainless steel
Motor Shaft 1117 carbon steel or 416 stainless steel* 1117 carbon steel
Gasket Neoprene Neoprene
  • Cert Sa
  • Cert Sspma
  • Cert Tough
  • Ce
  • Cert Tough