Features and Benefits
- 5-year warranty
- Corrosion-resistant, powder coated epoxy finish
- Durable, cast iron construction
- Cast iron switch case, motor, pump housing and base
- Viton outer switch boot
- No sheet metal parts to rust or corrode
- All castings are cast iron class 25-30 25000# tensile strength
- Stainless steel screws, guard, handle, arm and seal assembly
- Float-operated, submersible, 2-pole mechanical switch integrating advanced switch technology
- Permanent split capacitor motor, oil-filled and hermetically-sealed, automatic reset thermal overload protection
- Bearings – upper and lower oil-fed cast iron
- Carbon and ceramic shaft seal
- Entire unit pressure-tested after assembly
- Watertight, neoprene square ring between motor and pump housing
- Maximum temperature for effluent or dewatering: 130 °F (54 °C)
- Passes 1/2” (12 mm) spherical solids
- No screens to clog
- 1-1/2” NPT discharge (1-1/2” x 2” PVC adapter included with BN and BE Models)
- On point: 9-1/2” (24 cm)
- Off point: 3” (8 cm)
- Major width: 10-1/8" (31 cm)
- Major height: 12-1/8" (30 cm)
- Simplex and duplex systems available
Consult Factory for Special Applications
- Electrical alternators for duplex systems are available and supplied with an alarm
- Mechanical alternators for duplex systems are available with or without alarm switches
- Variable level float switches are available for controlling single and three phase systems
- Refer to FM1922 and FM0806 for temperatures above 130 °F (54 °C)
Notes
The sizing of effluent systems normally requires variable level float(s) controls and properly sized basins to achieve required pumping cycles or dosing timers with non-automatic pumps.
Reserve Powered Design.
For unusual conditions a reserve safety factor is engineered into the design of every Zoeller pump.
Product Specifications
60hz | 50hz | |
---|---|---|
Motor | 1/2 | |
Voltage | 115 | |
Phase | 1 Ph | |
Hertz | 60 Hz | |
RPM | 3450 | |
Type | Permanent split capacitor | |
Insulation | Class B | |
Amps | 10.5 | |
Operation | Automatic | |
Auto On / Off Points | 9-1/2" (24 cm) / 2-1/2" (6.4 cm) | |
Discharge Size | 1-1/2" NPT | |
Solids Handling | 1/2" (12 mm) spherical solids | |
Cord Length | 15' (4.6 m) | |
Cord Type | UL listed, 3-wire, grounded plug | |
Max Head | 26' (7.9 m) | |
Max Flow Rate | 80 GPM (303 LPM) | |
Max Operating Temperature | 130° F (54° C) | |
Cooling | Oil filled | |
Motor Protection | Auto reset thermal overload | |
Cap | Cast iron | |
Motor Housing | Cast iron | |
Pump Housing | Cast iron | |
Base | Cast iron | |
Upper Bearing | Sleeve bearing | |
Lower Bearing | Ball bearing | |
Mechanical Seals | Carbon and ceramic | |
Impeller Type | Non-clogging vortex | |
Impeller | Engineered thermoplastic | |
Hardware | Stainless steel | |
Motor Shaft | AISI 1215 cold rolled steel | |
Gasket | Neoprene | |
|
Technical Data
Caution
All installation of controls, protection devices and wiring should be done by a qualified licensed electrician. All electrical and safety codes should be followed including the most recent National Electric Code (NEC) and the Occupational Safety and Health Act (OSHA).
Selection Guide
- Integral float operated mechanical switch, no external control required.
- For automatic use, single piggyback variable level float switch or double piggyback variable level float switch. Refer to FM0477.
- See FM1228 for correct model of simplex control panel.
- See FM0712 for correct model of duplex control panel.
- To select an appropriate basin, go to Basins.
Accessories
Model Comparison Charts
- Product Model Comparison Chart: 60hz
model seal mode volts phase amps hp hz lbs kg M95 Single Auto 115 0 10.5 1/2 60