130 Series Effluent Pumps

Sump and Effluent Pumps // Effluent Pumps // Flow-Mate

130 Series Effluent Pumps

Effluent or dewatering submersible pump for septic tank, low pressure pipe (LPP) and enhanced flow STEP systems.

Features and Benefits

  • Castings - Model 137, all cast iron ASTM class 25, 2500# tensile strength. Model 139, all bronze.
  • Corrosion-resistant, powder coated epoxy finish (model 137)
  • Durable, cast iron construction - switch case motor and pump housing, base and impeller
  • Float-operated, 2-pole mechanical switch (automatic units only)
  • No sheet metal parts to rust or corrode
  • Oil-filled and hermetically-sealed, automatic reset thermal overload protected (1 Ph) motor
  • Upper and lower sleeve bearings running in bath of oil
  • Carbon and ceramic shaft seal
  • Stainless steel screws, bolts, guard, handle, arm and seal assembly
  • Maximum temperature for effluent or dewatering: 130 °F (54 °C) (extra duty: 140 °F / 60 °C)
  • Passes 5/8” (16 mm) spherical solids
  • No screens to clog
  • 1-1/2” NPT discharge (1-1/2” x 2” PVC Adapter fitting included with BN and BE Models)
  • On point: 10” (25.4 cm)
  • Off point: 2-3/4” (7 cm)
  • Simplex and duplex package systems available
  • Variable level control systems available, designed for heavy-duty effluent applications
  • Automatic and non-automatic models available

Consult Factory for Special Application

  • Electrical alternators for duplex systems are available and supplied with an alarm
  • Mechanical alternators for duplex systems are available with or without alarm switches
  • Simplex panels are available for 3 Ph pumps
  • Control alarm systems are available for 1 Ph pumps
  • Variable level control switches are available for controlling 1 and 3 Ph systems
  • Double piggyback, variable level float switches are available for variable level long cycle controls
  • Over 130 °F (54 °C) - special quotation required
  • Consult factory for temperatures over 130 °F (54 °C)

Notes

The sizing of effluent systems normally requires variable level float(s) controls and properly sized basins to achieve required pumping cycles or dosing timers with non-automatic pumps.

Pumps must be operated in upright position.

Reserve Powered Design.

For unusual conditions a reserve safety factor is engineered into the design of every Zoeller pump.

Product Specifications

60hz 50hz
Motor 1/2 HP 0.7 kW
Voltage 115 - 460 V 220 or 380 V
Phase 1 or 3 Ph 1 Ph or 3 Ph
Hertz 60 Hz 50 Hz
RPM 1750 RPM 1400 RPM
Type Split phase or 3 phase Split phase
Insulation Class B Class B
Amps 1.4 - 10.7 Amps 4.2 A
Operation Automatic or nonautomatic Automatic or nonautomatic
Auto On / Off Points 10" / 2-3/4" (25.4 cm / 7 cm) 25.4 cm / 7 cm (10" / 2-3/4")
Discharge Size 1-1/2" NPT 1-1/2" NPT (CE models with BSPT)
Solids Handling 5/8" (15 mm) spherical solids 15 mm (5/8") spherical solids
Cord Length 10' (3 m) auto, 15' (5 m) nonauto 3 m (9') standard
Cord Type UL listed, 3-wire neoprene cord SOW/SOOW (CE model H07RN-F)
Max Head 26' (8 m) 5.3 m (17.5')
Max Flow Rate 93 GPM (352 LPM) 15.9 m3/hr (70 GPM)
Max Operating Temperature 130 °F (54 °C) 54 °C (130 °F)
Cooling Oil filled Oil filled
Motor Protection Auto reset thermal overload (1 Ph) Auto reset thermal overload (1 Ph)
Cap Cast iron or bronze Cast iron or bronze
Motor Housing Cast iron or bronze Cast iron or bronze
Pump Housing Cast iron or bronze Cast iron or bronze
Base Cast iron or bronze Cast iron or bronze
Upper Bearing Sleeve bearing or bronze Sleeve bearing
Lower Bearing Sleeve bearing or bronze Sleeve bearing
Mechanical Seals Carbon and ceramic Carbon and ceramic
Impeller Type Non-clogging vortex Non-clogging vortex
Impeller Cast iron or bronze Cast iron or bronze
Hardware Stainless steel Stainless steel
Motor Shaft AISI 1215 cold roll steel AISI 1215 cold roll steel
Gasket Neoprene Neoprene
  • 151328 63
  • Cert Sa
  • Cert Sspma
  • Cert Tough
  • Ce
  • Cert Tough

Technical Data

Caution

All installation of controls, protection devices and wiring should be done by a qualified licensed electrician. All electrical and safety codes should be followed including the most recent National Electric Code (NEC) and the Occupational Safety and Health Act (OSHA).

Selection Guide

  1. Integral float operated mechanical switch, no external control required.
  2. For automatic use, single piggyback variable level float switch or double piggyback variable level float switch. Refer to FM0477.
  3. See FM1228 for correct model of simplex control panel.
  4. See FM0712 for correct model of duplex control panel.
  5. To select an appropriate basin, go to Basins.

Accesories

Model Comparison Charts

  • Product Model Comparison Chart: 60hz
    model seal mode volts phase amps hp hz lbs kg
    M137 Single Auto 115 0 10.7 1/2 60 47 21
    N137 Single Non 115 0 10.7 1/2 60 46 21
    BN137 Single Auto 115 0 10.7 1/2 60 48 22
    D137 Single Auto 230 0 5.8 1/2 60 47 21
    E137 Single Non 230 0 5.8 1/2 60 48 22
    H137 Single Auto 200 0 6.2 1/2 60 48 22
    I137 Single Non 200 0 6.2 1/2 60 48 22
    J137 Single Non 200 3 2.6 1/2 60 46 21
    F137 Single Non 230 3 2.6 1/2 60 48 22
    G137 Single Non 460 3 1.4 1/2 60 48 22
    BE137 Single Auto 230 0 5.8 1/2 60 48 22
    M139 Single Auto 15 0 10.7 1/2 60 51 23
    N139 Single Non 115 0 10.7 1/2 60 51 23
    D139 Single Auto 230 0 5.8 1/2 60 47 21
    E139 Single Non 230 0 5.8 1/2 60 48 22
    H139 Single Auto 200 0 6.2 1/2 60 48 22
    I139 Single Non 200 0 6.2 1/2 60 48 22
    J139 Single Non 200 3 2.6 1/2 60 48 22
    F139 Single Non 460 3 2.6 1/2 60 48 22
    G139 Single Non 460 3 1.4 1/2 60 48 22

Design Tools

Sales and Marketing

Sales Literature

Technical Support

Technical Support Literature