180, 190 Series Effluent Pumps

Sump and Effluent Pumps // Commercial Use Sump and Effluent Pumps // High Head Flow-Mate

180, 190 Series Effluent Pumps

Effluent or dewatering submersible pump for septic tank, low pressure pipe (LPP) and enhanced flow STEP systems.

Features and Benefits

  • Non-clogging vortex impeller design, bronze class 88-8-0-4 (180 series)
  • Enclosed impeller design (model 191, 60 Hz only)
  • Float-operated, submersible, 2-pole mechanical switch
  • Durable, cast iron construction
  • Cast iron switch case, base, motor and pump housing
  • No sheet metal parts to rust or corrode
  • Stainless steel screws, bolts, float rod, handle, guard, arm and seal assembly
  • Oil-filled, hermetically-sealed, automatic reset thermal overload protection (1 Ph only)
  • Maximum temperature for effluent or dewatering: 130 °F (54 °C), WD189 (60 Hz): 120 °F (49 °C)
  • Variable level control systems available
  • Neoprene square ring and gasket
  • Stainless steel carbon and ceramic rotary shaft seal
  • SAE 1117 carbon steel motor shaft (single seal only)
  • Upper and lower ball bearing running in bath of oil
  • All 180/4180 series pumps pass 3/4” (19 mm) spherical solids.
  • Model 191 passes 5/8” (16 mm) spherical solids.
  • On point: 14-3/4” (37.5 cm)
  • Off point: 5-1/4” (12.7 cm)
  • Major width: 12-3/4" (32.4 cm) (single seal pumps)
  • Major height: 19-5/16" (49.1 cm) (single seal pumps)
  • 1-1/2” NPT discharge with 2” or 3” flange available
  • Model 191 not available with 3” flange
  • Corrosion-resistant, powder coated epoxy finish
  • Automatic units not recommended for use in effluent systems

Models 4185, 4186, 4188, 4189 Double Seal Pumps (60 Hz, non-automatic only):

  • Protects motor from seal leaks
  • Improved bearing lubrication
  • Helps eliminate seal and bearing damage from dry runs
  • 416 stainless steel motor shaft
  • Major width: 12-3/4" (32.4 cm)
  • Major height: 21-3/16" (53.8 cm)

Notes

Note: The sizing of effluent systems normally requires variable level float(s) controls and properly sized basins to achieve required pumping cycles or dosing timers with non-automatic pumps.

Note: No UL listing for 200/208 V, 1 Ph pumps, models 186 & 191, or double seal series. See charts for UL & CSA listings.

Reserve Powered Design.
For unusual conditions a reserve safety factor is engineered into the design of every Zoeller® pump.

Product Specifications

60hz 50hz
Motor 1 - 2 HP 2.0 - 2.9 kW
Voltage 200 - 575 V 220 V or 380 V
Phase 1 or 3 Ph 1 Ph or 3 Ph
Hertz 60 Hz 50 Hz
RPM 3450 RPM 2800 RPM
Type Permanent split capacitor or 3 Ph Permanent split capacitor or 3 Ph
Insulation Class B/185 & 4185, Class F/186-191 & 4186-4189 Class B
Amps 3.3 - 20.5 Amps 4.1 - 14.2 A
Operation Automatic or nonautomatic Automatic or nonautomatic
Auto On / Off Points 15-3/4" (400 mm) / 5-1/4" (133 mm) 40 cm / 13.3 cm (15-3/4" / 5-1/4")
Discharge Size 1-1/2" NPT (optional 2" or 3" flange) 1-1/2" NPT (2" or 3" flange available) (CE models with BSPT)
Solids Handling 180/4180: 3/4" (19 mm), 191: 5/8" (15 mm) spherical solids 19 mm (3/4") spherical solids
Cord Length 20' (6 m) standard 6 m (20') standard
Cord Type UL listed, 3-wire neoprene cord and plug (1 Ph) or 4-wire cord with no plug (3 Ph) SOW/SOOW (CE H07RN-F)
Max Head 137' (42 m) 21.6 m (71')
Max Flow Rate 145 GPM (549 LPM) 27.5 m3/hr (120 gpm)
Max Operating Temperature 130 °F (54 °C), (model WD189 120 °F [49 °C]) 54°C (130°F)
Cooling Oil filled Oil filled
Motor Protection Auto reset thermal overload (1 Ph) Auto reset thermal overload (1 Ph)
Cap Cast iron Cast iron
Motor Housing Cast iron Cast iron
Pump Housing Cast iron Cast iron
Base Cast iron Cast iron
Upper Bearing Ball bearing Ball bearing
Lower Bearing Ball bearing Ball bearing
Mechanical Seals Carbon and ceramic Carbon and ceramic
Impeller Type Non-clogging vortex Non-clogging vortex
Impeller Bronze Bronze
Hardware Stainless steel Stainless steel
Motor Shaft 1117 carbon steel or 416 stainless steel* Carbon steel SAE 1117
Gasket Neoprene Neoprene
  • Cert Sa
  • Cert Tough
  • Cert Sspma
  • 151328 63
  • Ce
  • Cert Tough

Technical Data

Caution

All installation of controls, protection devices and wiring should be done by a qualified licensed electrician. All electrical and safety codes should be followed including the most recent National Electric Code (NEC) and the Occupational Safety and Health Act (OSHA).

Model 185 should not be subjected to heads less than 30' (10 m) TDH.

No UL listing for 200 V, 1 Ph pumps, models 186 & 191, or double seal series.

Selection Guide

  1. Integral float operated mechanical switch, no external control required.
  2. For automatic use single piggyback variable level float switch or double piggyback variable level float switch. Refer to FM0477.
  3. See FM1228 for correct model of simplex control panel.
  4. See FM0712 for correct model of duplex control panel.
  5. Variable level control switch 10-0743 used as a control activator, specify simplex (3) float or duplex (4) float system. Refer to FM0526.
  6. To select an appropriate basin, go to Basins.

* No Molded Plug (1) UL Listed unit available with 20 Amp Plug (2) CSA Approval without plug cap. (3) 20 Amp Outlet, P/N 10-0060 must be used.

Accessories

Design Tools

Sales and Marketing

Sales Literature

Technical Support

Technical Support Literature