Welcome to our NEW website!

X

Model 95

img-title
Sump and Effluent Pumps // Residential Use // Flow-Mate

Model 95

PREMIUM SERIES submersible pump for dewatering (sump) systems

Features and Benefits

  • 5-year warranty
  • Corrosion-resistant, powder coated epoxy finish
  • Durable, cast iron construction
  • Cast iron switch case, motor, pump housing and base
  • Viton outer switch boot
  • No sheet metal parts to rust or corrode
  • All castings are cast iron class 25-30 25000# tensile strength
  • Stainless steel screws, guard, handle, arm and seal assembly
  • Float-operated, submersible, 2-pole mechanical switch integrating advanced switch technology
  • Permanent split capacitor motor, oil-filled and hermetically-sealed, automatic reset thermal overload protection
  • Bearings – upper and lower oil-fed cast iron
  • Carbon and ceramic shaft seal
  • Entire unit pressure-tested after assembly
  • Watertight, neoprene square ring between motor and pump housing
  • Maximum temperature for effluent or dewatering: 130 °F (54 °C)
  • Passes 1/2” (12 mm) spherical solids
  • No screens to clog
  • 1-1/2” NPT discharge (1-1/2” x 2” PVC adapter included with BN and BE Models)
  • On point: 9-1/2” (24 cm)
  • Off point: 3” (8 cm)
  • Major width: 10-1/8" (31 cm)
  • Major height: 12-1/8" (30 cm)
  • Simplex and duplex systems available

Consult Factory for Special Applications

  • Electrical alternators for duplex systems are available and supplied with an alarm
  • Mechanical alternators for duplex systems are available with or without alarm switches
  • Variable level float switches are available for controlling single and three phase systems
  • Refer to FM1922 and FM0806 for temperatures above 130 °F (54 °C)

Notes 

The sizing of effluent systems normally requires variable level float(s) controls and properly sized basins to achieve required pumping cycles or dosing timers with non-automatic pumps.



Reserve Powered Design.
For unusual conditions a reserve safety factor is engineered into the design of every Zoeller pump.

Product Specifications

60hz 50hz
Motor 1/2
Voltage 115
Phase 1 Ph
Hertz 60 Hz
RPM 3450
Type Permanent split capacitor
Insulation Class B
Amps 10.5
Operation Automatic
Auto On / Off Points 9-1/2" (24 cm) / 2-1/2" (6.4 cm)
Discharge Size 1-1/2" NPT
Solids Handling 1/2" (12 mm) spherical solids
Cord Length 15' (4.6 m)
Cord Type UL listed, 3-wire, grounded plug
Max Head 26' (7.9 m)
Max Flow Rate 80 GPM (303 LPM)
Max Operating Temperature 130° F (54° C)
Cooling Oil filled
Motor Protection Auto reset thermal overload
Cap Cast iron
Motor Housing Cast iron
Pump Housing Cast iron
Base Cast iron
Upper Bearing Sleeve bearing
Lower Bearing Ball bearing
Mechanical Seals Carbon and ceramic
Impeller Type Non-clogging vortex
Impeler Engineered thermoplastic
Hardware Stainless steel
Motor Shaft AISI 1215 cold rolled steel
Gasket Neoprene
  • Cert 60Hz
  • Cert Sa
  • Cert Sspma
  • Cert Tough

Technical Data

CAUTION

All installation of controls, protection devices and wiring should be done by a qualified licensed electrician. All electrical and safety codes should be followed including the most recent National Electric Code (NEC) and the Occupational Safety and Health Act (OSHA).

SELECTION GUIDE

  1. Integral float operated mechanical switch, no external control required.
  2. For automatic use, single piggyback variable level float switch or double piggyback variable level float switch. Refer to FM0477.
  3. See FM1228 for correct model of simplex control panel.
  4. See FM0712 for correct model of duplex control panel.
  5. To select an appropriate basin, go to Basins.

Optional Pump Stand P/N 10-2421

ACCESSORIES

Model Comparison Charts

Pump Performance Curves

Design Tools