North America / English Change

 

High Head Flow-Mate
160 Series

Effluent or dewatering submersible pumps for septic tanks, low pressure pipe (LPP) and enhanced flow STEP systems.

 
 
Features andBenefits
ProductSpecifications
TechnicalData
Literature and Documents

  • Durable, cast iron constructed switch case, base, motor and pump housing
  • Cast iron Class 25-30 (25,000X tensile strength)
  • Impeller - bronze class 85-5-5-5
  • Corrosion-resistant, powder coated epoxy finish
  • Oil-filled, hermetically-sealed, automatic reset thermal overload protected (1 Ph only) motor
  • Upper and lower ball bearing running in bath of oil
  • Carbon and ceramic shaft seal
  • SAE 1117 carbon steel motor shaft (single seal models only)
  • Maximum temperature for effluent or dewatering: 130° F (54° C) (E/D: 140°F / 60°C)
  • Major width: 12-3/4" (32 cm)
  • Major height: 19-5/16" (49 cm)
  • No screens to clog
  • Neoprene square ring & gasket
  • Stainless steel screws, bolts, float rod, handle, guard, arm and seal assembly
  • Passes ¾” (19 mm) spherical solids
  • 1½” NPT discharge with 2” or 3” flange available
  • Automatic units available with float-operated, submersible, 2-pole mechanical switch
  • On: point 14 ¾” (37.5 cm)
  • Off: point 5” (12.7 cm)
  • 100% of units are computerized tested

Models 4161, 4163, 4165 double seal pumps available (60 Hz, nonautomatic only):

  • Protects motor from seal leaks
  • Improved bearing lubrication
  • Helps eliminate seal and bearing damage from dry runs
  • 416 stainless steel motor shaft
  • Major width: 12¾” (32 cm)
  • Major height: 21-3/16” (53.8 cm)

HERTZ
60 Hz
MOTOR
1/2 or 1 HP
VOLTAGE
115 - 575 V
PHASE
1 or 3 Ph
RPM
3450 RPM
TYPE
Permanent split capacitor or 3 phase
INSULATION
Class B
AMPS
2.4 - 15.5 Amps
OPERATION
Automatic and nonautomatic
AUTO ON/ OFF POINTS
15-3/4" / 5-1/4" (40 cm / 13.3 cm)
DISCHARGE SIZE
1-1/2" NPT (optional 2" or 3" flange)
SOLIDS HANDLING
3/4" (19 mm) spherical solids
CORD LENGTH
20' (6 m) standard
CORD TYPE
UL listed, 3-wire neoprene cord and plug (1 Ph) or 4-wire cord with no plug (3 Ph)
MAX HEAD
86.5' (26 m)
MAX FLOW RATE
100 GPM (379 LPM)
MAX OPERATING TEMP
130° F (54° C)
COOLING
Oil filled
MOTOR PROTECTION
Auto reset thermal overload (1 Ph)
CAP
Cast iron
MOTOR HOUSING
Cast iron
PUMP HOUSING
Cast iron
BASE
Cast iron
UPPER BEARING
Ball bearing
LOWER BEARING
Ball bearing
MECHANICAL SEALS
Carbon and ceramic
IMPELLER TYPE
Non-clogging vortex
IMPELLER
Bronze
HARDWARE
Stainless Steel
MOTOR SHAFT
SAE 1117 carbon steel or 416 stainless steel*
GASKET
Neoprene square ring & gasket
  • 54
  • 2
  • 8
  • 11
  • 13

 

×

 

×