North America / English Change

 

Drain Pump Series

Removes water from areas where gravity flow is not available.

 
 
 
Features andBenefits
ProductSpecifications
TechnicalData
Literature and Documents

  • Applications include laundry tray pump, wet bar sink, lavatory, air conditioning condensate and dehumidifier water removal. Can also be used in conjunction with dishwashers and garbage disposal.
  • No inlet filters or screens to clean
  • Optional top or side inlet
  • Can be installed with internal trap
  • Automatic pumps with tank cord seals
  • All hardware for easy assembly
  • Polypropylene basin and lid
  • Internal discharge pipe to lid (trap supplied by others)
  • Check valve (30-0181, not included with model 104)
  • Contact factory for additional inlet option or high head applications
  • Easy installation, no need to dig a sump
  • 132 comes preassembled

 

Pump features (models 53, 55, 57, 59, 98):

  • Passes laundry lint
  • Automatic, float-operated mechanical switch
  • 9' (3 m), UL listed, 3-wire cord and plug (15' [5 m] cord standard on model 98)
  • Stainless steel screws, guard, handle and switch arm
  • Passes ½” (12.7 mm) spherical solids
  • 1 ½” NPT discharge
  • 1550 RPM on 50 series
  • 1725 RPM on model 98
  • Non-clogging vortex impeller
  • Glass-filled, polypropylene base with built-in strainer
  • Model 59 - all bronze construction
  • Models 57 and 98 - all cast iron construction
  • Temperature rated 130°F (55°C)
  • UL and cCSAus listed pump

Model 72:

  • Passes laundry lint
  • 9' (3 m), UL-listed, 3-wire cord and plug
  • Stainless steel screws, switch arm and lower motor housing
  • Oil-free
  • Passes 3/8” (9.5 mm) spherical solids
  • 1½” NPT discharge
  • 3400 RPM
  • Non-clogging vortex impeller
  • Temperature rated 110°F (43°C)
  • cCSAus listed pump

Basin:

  • Polypropylene construction
  • Corrosion-resistant
  • High capacity
  • Gasket-sealed polypropylene lid
  • 2” NPT vent
  • 1½” NPT discharge
  • 1½” compression slip fit for top and side intake. Note: 132 comes preassembled, for side inlet only
  • Threaded connections for easy installation
  • May be installed with internal trap for space savings
  • Gas-tight cover
  • Temperature rated 130°F (55°C)
  • Fits under most sinks
  • Basin passes 10’ (3 m) stack test – Models 104 and 132 will not pass 10’ (3 m) stack test

Check valve (excluding model 104)(30-0181)

  • “Full Flow” design
  • 1 ½” or 1 ¼" slip x slip union
  • PVC construction
  • For additional specifications, see FM0217 
Notes

Product may not be exactly as pictured.

Note: For additional inlet option or high head applications, consult factory.

Reserve Powered Design.

For unusual conditions a reserve safety factor is engineered into the design of every Zoeller pump.

HERTZ
60 Hz
MOTOR
1/3 - 1/2 HP
VOLTAGE
115 V
PHASE
1 Ph
RPM
1550 - 3400 RPM
DISCHARGE SIZE
1-1/2" NPT
SOLIDS HANDLING
0.5" (1.27 cm) spherical
CORD LENGTH
9 ft (3m) or 15 ft (5m) standard
CORD TYPE
UL listed, 3-wire cord and plug
MAX OPERATING TEMP
130° F (55° C)
MOTOR HOUSING
Bronze or cast iron
PUMP HOUSING
Bronze or cast iron
BASE
Glass-filled polypropylene, bronze or cast iron
IMPELLER TYPE
Non-clogging vortex
HARDWARE
Stainless steel
  • 54
  • 11
  • 13
  • 16

Warning

To reduce the risk of electrical shock, a properly grounded receptacle of grounding type shall be installed and protected by a ground fault circuit interrupter (GFCI) in accordance with national electrical code and local codes. Do not remove ground pin from plug. FOR ABOVE-GROUND INSTALLATION ONLY.

 

×
×