Latin America / English Change

 

Waste-Mate
400 Series

Single and double seal submersible sewage or dewatering pumps.

 
 
Features andBenefits
ProductSpecifications
TechnicalData
Literature and Documents

  • Cast iron casting, class 25-30 25000# tensile strength
  • Oil-filled, hermetically-sealed, automatic reset thermal overload protected (1 Ph only) motor
  • Upper and lower ball bearing running in bath of oil
  • Mechanical shaft seal - carbon and ceramic rotary face seal, with stainless steel wetted parts
  • 1117 carbon steel motor shaft (single seal models)
  • Stainless steel screws, bolts, washers and lifting bracket
  • Neoprene square ring and gasket
  • Maximum temperature: 130°F (54°C) standard
  • Variable level controls available
  • 4” horizontal flanged discharge, standard ANSI flange
  • Passes 3” (76 mm) spherical solids
  • Corrosion-resistant, powder coated epoxy finish
  • Non-automatic available
  • Applications include:
    • High capacity water removal - parking lots, low flood areas, water transfer
    • To meet 3" intake, 4" discharge code requirements on some sewage applications
    • Retrofit on existing sewage installations
    • New installations

Model 4404, 4405 double seal pumps (non-automatic):

  • Protects motor from seal leaks
  • Improved seal lubrication
  • Helps eliminate seal and bearing damage from dry runs
  • 416 stainless steel motor shaft
  • Major width: 16-1/8” (41 cm)
  • Major height: 2 ½” (69.9 cm)

Guide rail systems:

  • 4” (DN100) pipe flange fittings
  • P/N 39-0016
  • Includes:
    • Cast iron discharge elbow
    • Stainless steel lower guides
    • Cast iron mounting plate
    • Stainless steel upper guide rail bracket
    • Optional intermediate stabilizer for systems over 15’ (5 m) deep (P/N 39-0013 carbon steel, P/N 39-0014 stainless steel)
    • Stainless steel guide brackets for pump mounting plate
    • Buna N gasket for mounting plate
    • Stainless steel bolts and lock washers
    • Features automatic engagement, easy disengagement and class 30 cast iron fittings
    • Uses 2” IPs guide rails and pull cable or chain (not furnished)

 

Consult factory for special applications:

  • Electrical alternators, for duplex systems
  • Mechanical alternators, for duplex systems (with or without high-water alarm functions)
  • Simplex control panels available
  • Variable level float switches are available for controlling single and three phase systems
  • Double piggyback float switches are available for variable level long cycle controls
  • Long cords available in lengths of 25' (8 m), 35’ (11 m) and 50’ (15 m)
  • Simplex and duplex basins available
Notes

The sizing of effluent systems normally requires variable level float(s) controls and properly sized basins to achieve required pumping cycles or dosing timers with non-automatic pumps.

 

Reserve powered design.

For unusual conditions a reserve safety factor is engineered into the design of every Zoeller pump.

HERTZ
60 Hz
MOTOR
2 or 3 HP
VOLTAGE
200 - 575 V
PHASE
1 or 3 Ph
RPM
1725 RPM
TYPE
Permanent split capacitor or 3 phase
INSULATION
Class B
AMPS
4.1 - 20.2 Amps
OPERATION
Automatic and nonautomatic
DISCHARGE SIZE
4" horizontal ANSI flange
SOLIDS HANDLING
3" (76 mm) spherical solids
CORD LENGTH
20' (6 m) standard
CORD TYPE
UL listed, 3-wire neoprene cord and plug
MAX HEAD
38' (11.6 m)
MAX FLOW RATE
361 GPM (1367 LPM)
MAX OPERATING TEMP
130° F (54° C)
COOLING
Oil filled
MOTOR PROTECTION
Auto reset thermal overload (1 Ph)
CAP
Cast iron
MOTOR HOUSING
Cast iron
PUMP HOUSING
Cast iron
BASE
Cast iron
UPPER BEARING
Ball bearing
LOWER BEARING
Ball bearing
MECHANICAL SEALS
Carbon and ceramic
IMPELLER TYPE
Non-clogging vortex
IMPELLER
Cast iron
HARDWARE
Stainless steel
MOTOR SHAFT
1117 carbon steel or 416 stainless steel*
GASKET
Neoprene
*Single seal models are built with a carbon steel motor shaft, and double seal models are built with a stainless steel motor shaft.
  • 54
  • 2
  • 8
  • 11

Caution

All installation of controls, protection devices and wiring should be done by a qualified licensed electrician. All electrical and safety codes should be followed including the most recent National Electric Code (NEC) and the Occupational Safety and Health Act (OSHA).

Selection Guide

  1. For automatic use single piggyback variable level float switch or double piggyback variable level float switch. Refer to FM0477.
  2. See FM1228 for correct model of simplex control panel.
  3. See FM0712 for correct model of duplex control panel.

20 amp outlet P/N 10-0060, must be used with model E405/4404 and WD405/4405.

Accessories

 

×

 

×