Latin America / English Change

 

Drain Pump Series

Removes water from areas where gravity flow is not available.

 
 
 
Features andBenefits
ProductSpecifications
TechnicalData
Literature and Documents

  • Applications include laundry tray pump, wet bar sink, lavatory, air conditioning condensate and dehumidifier water removal. Can also be used in conjunction with dishwashers and garbage disposal.
  • No inlet filters or screens to clean
  • Optional top or side inlet
  • Can be installed with internal trap
  • Automatic pumps with tank cord seals
  • All hardware for easy assembly
  • Polypropylene basin and lid
  • Internal discharge pipe to lid (trap supplied by others)
  • Check valve (30-0181, not included with model 104)
  • Contact factory for additional inlet option or high head applications
  • Easy installation, no need to dig a sump
  • 132 comes preassembled

 

Pump features (models 53, 55, 57, 59, 98):

  • Passes laundry lint
  • Automatic, float-operated mechanical switch
  • 9' (3 m), UL listed, 3-wire cord and plug (15' [5 m] cord standard on model 98)
  • Stainless steel screws, guard, handle and switch arm
  • Passes ½” (12.7 mm) spherical solids
  • 1 ½” NPT discharge
  • 1550 RPM on 50 series
  • 1725 RPM on model 98
  • Non-clogging vortex impeller
  • Glass-filled, polypropylene base with built-in strainer
  • Model 59 - all bronze construction
  • Models 57 and 98 - all cast iron construction
  • Temperature rated 130°F (55°C)
  • UL and cCSAus listed pump

Model 72:

  • Passes laundry lint
  • 9' (3 m), UL-listed, 3-wire cord and plug
  • Stainless steel screws, switch arm and lower motor housing
  • Oil-free
  • Passes 3/8” (9.5 mm) spherical solids
  • 1½” NPT discharge
  • 3400 RPM
  • Non-clogging vortex impeller
  • Temperature rated 110°F (43°C)
  • cCSAus listed pump

Basin:

  • Polypropylene construction
  • Corrosion-resistant
  • High capacity
  • Gasket-sealed polypropylene lid
  • 2” NPT vent
  • 1½” NPT discharge
  • 1½” compression slip fit for top and side intake. Note: 132 comes preassembled, for side inlet only
  • Threaded connections for easy installation
  • May be installed with internal trap for space savings
  • Gas-tight cover
  • Temperature rated 130°F (55°C)
  • Fits under most sinks
  • Basin passes 10’ (3 m) stack test – Models 104 and 132 will not pass 10’ (3 m) stack test

Check valve (excluding model 104)(30-0181)

  • “Full Flow” design
  • 1 ½” or 1 ¼" slip x slip union
  • PVC construction
  • For additional specifications, see FM0217 
Notes

Product may not be exactly as pictured.

Note: For additional inlet option or high head applications, consult factory.

Reserve Powered Design.

For unusual conditions a reserve safety factor is engineered into the design of every Zoeller pump.

HERTZ
60 Hz
MOTOR
1/3 - 1/2 HP
VOLTAGE
115 V
PHASE
1 Ph
RPM
1550 - 3400 RPM
DISCHARGE SIZE
1-1/2" NPT
SOLIDS HANDLING
0.5" (1.27 cm) spherical
CORD LENGTH
9 ft (3m) or 15 ft (5m) standard
CORD TYPE
UL listed, 3-wire cord and plug
MAX OPERATING TEMP
130° F (55° C)
MOTOR HOUSING
Bronze or cast iron
PUMP HOUSING
Bronze or cast iron
BASE
Glass-filled polypropylene, bronze or cast iron
IMPELLER TYPE
Non-clogging vortex
HARDWARE
Stainless steel
  • 54
  • 11
  • 13
  • 16
HERTZ
50 Hz
MOTOR
0.56 - 0.72 KW
VOLTAGE
220 V
PHASE
1 Ph
RPM
1400 or 2800 RPM
TYPE
Shaded pole or permanent split capacitor
INSULATION
Class B
AMPS
3.6 - 5.2 Amps
OPERATION
Automatic
AUTO ON/ OFF POINTS
18.4 cm / 7.6 cm (7-1/4" / 3")
DISCHARGE SIZE
1-1/2" NPT
SOLIDS HANDLING
12 or 19 mm (1/2" or 3/4") spherical solids
CORD LENGTH
3 or 5 m (9' or 15') standard
CORD TYPE
2-wire plus ground
MAX HEAD
4.7m (15.5')
MAX FLOW RATE
255 LPM (56 GPM)
MAX OPERATING TEMP
54°C (130°F)
COOLING
Oil filled
MOTOR PROTECTION
Auto reset thermal overload
CAP
Cast iron
MOTOR HOUSING
Cast iron
PUMP HOUSING
Cast iron
BASE
Engineered plastic or cast iron
UPPER BEARING
Sleeve bearing
LOWER BEARING
Sleeve or ball bearing
MECHANICAL SEALS
Carbon and ceramic
IMPELLER TYPE
Non-clogging vortex
IMPELLER
Engineered plastic
HARDWARE
Stainless steel
MOTOR SHAFT
AISI 1215 steel
GASKET
Neoprene
  • 14
  • 11
  • 16

Warning

To reduce the risk of electrical shock, a properly grounded receptacle of grounding type shall be installed and protected by a ground fault circuit interrupter (GFCI) in accordance with national electrical code and local codes. Do not remove ground pin from plug. FOR ABOVE-GROUND INSTALLATION ONLY.

 

×

 

×