Latin America / English Change

 

Qwik Jon® Ultima 204

Economical lavatory and shower system designed for free-standing or built-in installation

 
 
Features andBenefits
ProductSpecifications
TechnicalData
Literature and Documents

Install a Qwik Jon® Ultima just about anywhere

  • Contains ½ HP mini-grinder pump
  • Dual cutting action provides over 70,000 cuts per minute (50 Hz: 60,000 cuts per minute), greatly reducing the potential for clogging and increasing pump reliability.
  • Preassembled pump and tank for easy installation
  • No need to destroy concrete floors
  • No need to elevate floor
  • Designed to accommodate a lavatory, bathtub and/or shower
  • Perfect for basements, cabins, workshops, garages, additions, pool houses, etc.
  • Reduces construction costs
  • 1” discharge (can be reduced to ¾” to replace existing systems)
  • Pumps any direction
  • Can be installed either free-standing or behind a wall with the 2” MPT or 1 1/2” internal slip side inlets
  • Note: These pumps are not designed for use in any other application.

Pump features:

  • Automatic level control switch
  • Thermal overload protected motor
  • Stainless steel screws, bolts and handle
  • Non-clogging vortex impeller
  • UL listed, 3-wire, neoprene 9' (3m) cord and plug
  • Maximum temperature 130°F (54°C)

Tank features:

  • Durable ABS tank with white finish
  • Light-weight
  • Built-in check valve

Items included:

  • Tank, lid and gasket
  • ½ HP mini-grinder pump
  • Back-flow device (check local codes)
  • 1” discharge and 1 ½” vent
  • Hardware pack
  • Installation instructions
  • Shipping weight: 33 lbs (15Kg)

Items needed by installer:

  • Supply fittings and waste pipe
  • Electrical source with ground fault interrupter (GFCI) protected receptacle
  • Water supply
  • Tools
Notes

Patent Pending

Note: These pumps not designed for use in any other application.

All installations of controls, protection devices and wiring should be done by a qualified licensed electrician. All electrical and safety codes should be followed including the most recent National Electric Code (NEC) and the Occupational Safety and Health Act (OSHA). Must be installed per local codes.

HERTZ
60 Hz
MOTOR
1/2 HP
DISCHARGE SIZE
1"
CORD LENGTH
9 ft (3m)
CORD TYPE
UL listed, 3-wire neoprene cord and plug
MAX OPERATING TEMP
130°F (54°C)
MOTOR PROTECTION
thermal overload
IMPELLER TYPE
Non-clogging vortex impeller
HARDWARE
stainless steel
  • 2
  • 13
HERTZ
50 Hz
MOTOR
0.7 KW
VOLTAGE
220 V
PHASE
1 Ph
RPM
2800 RPM
TYPE
Permanent split capacitor
INSULATION
Class B
AMPS
3.4 Amps
OPERATION
Automatic
AUTO ON/ OFF POINTS
Preset
DISCHARGE SIZE
1"
COOLING
Oil filled
MOTOR PROTECTION
Auto reset thermal overload
CAP
Engineered thermoplastic
MOTOR HOUSING
Cast iron
PUMP HOUSING
Engineered thermoplastic
BASE
Engineered thermoplastic
UPPER BEARING
Ball bearing
LOWER BEARING
Ball bearing
MECHANICAL SEALS
Carbon and ceramic
IMPELLER TYPE
Non-clogging vortex
IMPELLER
Engineered plastic
HARDWARE
Stainless steel
MOTOR SHAFT
AISI 1215 cold rolled steel
GASKET
Closed cell tank gasket; BUNA-N pump gaskets
  • 14
  • 28
  • 16

 

×

 

×