Europe, Middle East and Africa / English Change

 

Waste-Mate
Model 264

Submersible sewage/effluent or dewatering pumps.

 
 
Features andBenefits
ProductSpecifications
TechnicalData
Literature and Documents

  • Float-operated, submersible (NEMA 6), 2-pole switch
  • Durable, cast iron construction - switch cap, motor and pump housing
  • Engineered plastic base
  • Stainless steel screws, bolts, handle, guard, arm and seal assembly
  • Corrosion-resistant, powder coated epoxy finish
  • Hermetically sealed, automatic reset thermal overload protection
  • Upper and lower sleeve bearings running in bath of oil
  • Carbon and ceramic shaft seal
  • Passes 2” (50 mm) spherical solids
  • 2” NPT discharge
  • On point: 12½” (31.8 cm)
  • Off point: 4½” (11.4 cm)
  • Simplex and duplex systems available
  • Automatic and nonautomatic models available
  • Nonautomatic for variable level systems
  • Models available packaged with piggyback variable level float switch

Consult factory for special applications:

  • Electrical alternators for duplex systems available with variable level float switches.
  • Minimum recommended basin size - simplex: 18” x 30” (45.7 x 76.2 cm), duplex: 30” x 36” (76.2 x 91.4 cm)
  • Standard automatic – 4/10 HP, 34.5 lbs.(15.6 Kg)
  • High water alarms available
  • Mechanical alternators available for duplex systems
  • The approximate gallons pumped out per cycle for standard models are:

    Tank Diameter

    Gallons / Liters Pumped

    18” (46 cm) simplex

    8 gallons / 36 liters

    24” (60 cm )simplex

    15 gallons / 68 liters

    30” (76 cm) duplex

    22 gallons / 100 liters

    36” (91 cm) duplex

    33 gallons / 150 liters

    48” (122 cm) duplex

    60 gallons / 273 liters

Notes

Note: The sizing of effluent systems normally requires variable level float(s) controls and properly sized basins to achieve required pumping cycles or dosing timers with non-automatic pumps.


Reserve powered design.

For unusual conditions a reserve safety factor is engineered into the design of every Zoeller pump.


*May be used in those states where codes do not restrict solids size in effluent systems.

HERTZ
60 Hz
MOTOR
4/10 HP
VOLTAGE
115 or 230 V
PHASE
1 Ph
RPM
1725 RPM
TYPE
Permanent split capacitor
INSULATION
Class B
AMPS
4.7 - 9.4 Amps
OPERATION
Automatic or nonautomatic
AUTO ON/ OFF POINTS
12-1/2" / 4-1/2 (31.8 cm / 11.4 cm)
DISCHARGE SIZE
2" NPT
SOLIDS HANDLING
2" (50 mm) spherical solids
CORD LENGTH
15' (5 m) standard
CORD TYPE
UL listed, 3-wire cord and plug
MAX HEAD
18' (5.5 m)
MAX FLOW RATE
90 GPM (341 LPM)
MAX OPERATING TEMP
130° F (54° C)
COOLING
Oil filled
MOTOR PROTECTION
Auto reset thermal overload
CAP
Cast iron
MOTOR HOUSING
Cast iron
PUMP HOUSING
Cast iron
BASE
Engineered plastic
UPPER BEARING
Sleeve bearing
LOWER BEARING
Sleeve bearing
MECHANICAL SEALS
Carbon and ceramic
IMPELLER TYPE
Non-clogging vortex
IMPELLER
Engineered plastic
HARDWARE
Stainless steel
MOTOR SHAFT
A151 1215 Steel
GASKET
Neoprene or Buna-N

  • 54
  • 2
  • 8
  • 11
  • 13
HERTZ
50 Hz
MOTOR
0.94 KW
VOLTAGE
220 V
PHASE
1 Ph
RPM
1400 RPM
TYPE
Permanent split capacitor
INSULATION
Class B
AMPS
4.9 Amps
OPERATION
Automatic and nonautomatic
AUTO ON/ OFF POINTS
31.8 cm / 11.4 cm (12-1/2" / 4-1/2")
DISCHARGE SIZE
2" NPT
SOLIDS HANDLING
50 mm (2") spherical solids
CORD LENGTH
5 m (15') standard
CORD TYPE
16-3 SJEOW
MAX HEAD
4.3 m (14')
MAX FLOW RATE
314 LPM (83 GPM)
MAX OPERATING TEMP
54 °C (130 °F)
COOLING
Oil filled
MOTOR PROTECTION
Auto reset thermal overload
CAP
Cast iron
MOTOR HOUSING
Cast iron
PUMP HOUSING
Cast iron
BASE
Engineered plastic
UPPER BEARING
Sleeve bearing
LOWER BEARING
Sleeve bearing
MECHANICAL SEALS
Carbon and ceramic
IMPELLER TYPE
Non-clogging vortex
IMPELLER
Engineered plastic with metal insert
HARDWARE
Stainless steel
MOTOR SHAFT
AISI 1215 or SAE 1045 steel
GASKET
Neoprene
  • 14
  • 28
  • 8

Selection Guide

  1. Integral float operated mechanical switch, no external control required.
  2. For automatic use single piggyback variable level float switch or double piggyback variable level float switch. Refer to FM0477.
  3. See FM1228 for correct model of simplex control panel.
  4. See FM0712 for correct model of duplex control panel.

Accessories

 

×

 

×